Technical Specifications
Materials
Steel
Connections
½" flow and return.
Test pressure
10.5 Bar
Testing authority
EN442
Maximum operating pressure
8 Bar
Maximum working temperature
95ºC
Packaging
Plastic wrapped in cardboard box
All products must be inspected once removed
from the packaging and your point of purchase
notified within 28 days of delivery of any scratches,
blemishes or other damage. Your point of purchase
will then agree appropriate action.
Imperfect radiators should therefore not be fitted
and we will not accept responsibility for replacement
of scratched or damaged radiators once they have
been fitted. This includes any consequential loss or
cost of fitting.
If we are not notified within 28 days of the date
on the signed delivery note then it will be deemed
that we have fully complied with our obligations
and claims will not be considered.
Failure to comply with any of the above may
invalidate any claims. We recommend that after you
check the product on delivery that it is stored in its
packaging to prevent damage prior to installation,
we cannot accept responsibility for items damaged
after delivery.
For full details of our Terms and Conditions please
visit www.supplies4heat.co.uk or call us on 01342
306880.
Terms & Conditions
This product is guaranteed for 10 years. The guarantees in all cases are subject to the
products being installed in accordance with British and or European standards as well as
these fitting instructions. The guarantees in all cases are restricted to the free of charge
replacement or repair of the failed product only. Our liability will under no circumstances
extend beyond the repair or replacement of the product supplied by us. Claims for either
labour in replacement or damage to property are not admissible. Any goods that are
returned, in the event of a problem, will belong to us.
Guarantees & Liabilities
PLEASE NOTE:
Systems using micro bore pipework must have adequate pressure
and flow rates for the number and style of radiators on the system
.
www.supplies4heat.co.uk 01342 306880
A brand of ; Italy’s leading manufacturer of design led radiators.
You should have:
• 1 Towel rail
• 4 Bracket Sleeves
• 4 Grub screws
You will need:
• Tape measure
• Electric drill and bits
• Spirit level
• Airvent key
• Appropriate wall fixings
• Spanner for valves and vents
2. Contents
Using the diagrams overleaf, mark the positions for the brackets on
the wall. The centre of the brackets are positioned 113 mm from the
top of the collectors, and 15 mm in from each side.
Hold up the bracket sleeve to the wall and using a suitable screw,
slide through the bracket and into the wall plug, and secure.
If the position is correct, we suggest marking and fixing the top
two brackets first, and then fixing the bottom brackets to ensure
accuracy.
3. Mark bracket positions
4. Fix Brackets
Please Note: In accordance with Part L1 2006 of
the Building Regulations and BS7593:1992 code of
practice for the treatment of hot water and central
heating systems, we strongly recommend flushing
the heating system post installation of new radiators
and then adding the correct quantity and type of
inhibitor for use with your radiator and system to
prevent corrosion. Damage caused to systems not
protected by a suitable inhibitor will not be covered
by manufacturer’s guarantee.
5. Commission Radiator
Please refer to the diagrams overleaf.
Cleaning:
Steel products can be cleaned using a soft damp cloth with
a non abrasive cleaning product.
1
2
3
4
Using suitable drill bits and plugs fit the wall plugs into the
wall to your previously made position markings.
Hold up the bracket sleeve to the wall, and using a suitable
screw or the one provided, slide through the bracket and
into the wall plug, and secure.
Repeat above steps for both top brackets.
Slide the towel rail into the brackets and check the positions
using a spirit level to ensure it is horzontally level.
If the positions is correct, repeat Section 3 and steps 1-3
for the two bottom brackets.
With all four bracket sleeves securely fixed to the wall,
lift the towel rail and slide into the bracket sleeves. Use
the supplied grub screw to insert into the side of the
bracket sleeve, and tighten to secure.
