background image

Chapter 7: BIOS

7-17

Password on Boot

This setting allows you to decide if a password is required for a user to access the 

system at the boot-up.  The options are 

Enabled

 (password required) and Disabled 

(password not required).

7-6 Boot

Choose Boot from the Phoenix BIOS Setup Utility main menu with the arrow keys.  You 

should see the following display.  See details on changing boot priority and devices in  

Specifi c Help Windows.  All Boot BIOS settings are described in this section.

Boot Priority Order/Excluded from Boot Orders

The devices included in the boot list section (above) are bootable devices listed in 

the sequence of boot order as specifi ed. The boot functions for the devices included 

in the candidate list (above) are currently disabled.  Use a <+> key or a <-> key to 

move the device up or down. Use the <f> key or the <r> key to specify the type of 

an USB device, either fi xed or removable. You can select one item from the boot 

list and hit the <x> key to remove it from the list of bootable devices (to make its 

resource available for other bootable devices). Subsequently, you can select an item 

from the candidate list and hit the <x> key  to remove it from the candidate list and 

put it in the boot list. This item will then become a bootable device. See details on 

changing the boot priority order of a device in the "Item Specifi c Help" window.

Candidate 
List

Boot List

Summary of Contents for SUPERSERVER 5015M-NT







































































































































Reviews: