Supero SUPER P4SGA User Manual Download Page 17 | Manualshive

Page: 17 / 93

background image

Chapter 1: Introduction

1-11

Motherboard Features

CPU

Latest CPU technology!

• Single Pentium

®

4 478-pin mPGA 1.5 - 3.06 GHz processors at a 533/

400 MHz system bus speed. P4SGL: 400 MHz system bus only.
(P4SGA+: same as P4SGA but also supports hyper-threading.)

Memory

Latest memory technology!

• Two 184-pin DIMM slots for up to 2 GB of non-ECC unbuffered

PC2100/1600 (DDR-266/200) SDRAM (PC2700/2100 for P4SGR/P4SGE/
P4SGA+)

Note:

See Section 2-4 for details.

Chipset

Latest Intel chipset technology!

• Intel 845G Chipset - P4SGA
• Intel 845GL Chipset - P4SGL
• Intel 845GE Chipset - P4SGR/P4SGE/P4SGA+

Expansion Slots

• Six 32-bit, 33 MHz PCI slots (P4SGA/P4SGL/P4SGA+)
• Five 32-bit, 33 MHz PCI slots (P4SGR/P4SGE)
• One 1.5V 4xAGP slot (P4SGA/P4SGR/P4SGE)

BIOS

With the latest voice BIOS technology for POST messaging!*

• 4 Mb Firmware Hub AwardBIOS

®

Flash BIOS

• APM 1.2, DMI 2.3, PCI 2.2, ACPI 1.0, Plug and Play (PnP)

PC Health Monitoring

• Nine onboard voltage monitors for CPU core, chipset voltage, +3.3V,

+3.3V standby,

+

5V, +5V standby, Vbat (battery voltage) and

±

12V

• Fan status monitor with firmware/software on/off control
• SuperDoctor II Utility
• Environmental temperature monitoring and control
• Power-up mode control for recovery from AC power loss
• System overheat LED and control
• System resource alert
• Hardware BIOS virus protection
• Auto-switching voltage regulator for the CPU core

*P4SGA/P4SGL/P4SGA+ only

«
...
15
16
17
18
19
...
»

Summary of Contents for SUPER P4SGA






























































































Reviews:

No comments

Related manuals for SUPER P4SGA

Brand: Abit Pages: 120

Brand: u-blox Pages: 25

Brand: Yamaha Pages: 96

Brand: Alcad Pages: 98

Brand: Linear Technology Pages: 16

Brand: Aaeon Pages: 97

Brand: Freetech Pages: 79

Brand: Intel Pages: 30

Brand: JETWAY Pages: 57

Brand: ASROCK Rack Pages: 83

Brand: Acorp Pages: 4

Brand: ETOP Pages: 68

Brand: Microchip Technology Pages: 54

Brand: MSI Pages: 48

Brand: Gigabyte Pages: 88

Brand: Xilinx Pages: 40

Brand: DFI Pages: 93

Brand: Hitachi Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands