Supermicro X9DRD-iF User Manual Download Page 38

Page: 38 / 115

2-12

X9DRD-iF/LF Motherboard User’s Manual

Memory Support for the X9DRD-iF/LF Motherboard

The X9DRD-iF/LF motherboard supports up to 512 GB of Load Reduced (LRDIMM),
256 GB of Registered (RDIMM) or 64 GB of Unbuffered (UDIMM) ECC/Non-ECC
DDR3 800/1066/1333/1600/1866 MHz 240-pin 4-channel memory modules in eight
DIMM slots.

Note:

For the latest memory updates, please refer to the Tested Memory

List posted on our website (http://www.supermicro.com/products/mother-
board).

Processor & Memory Module Population Configuration

For memory to work properly, follow the tables below for memory installation.

Processors and their Corresponding Memory Modules

CPU#

Corresponding DIMM Modules

CPU1

P1-DIMMA1

P1-DIMMB1

P1-DIMMC1

P1-DIMMD1

CPU2

P2-DIMME1

P2-DIMMF1

P2-DIMMG1

P2-DIMMH1

Processor and Memory Module Population

Number of

CPUs+DIMMs

CPU and Memory Population Configuration Table

(*For memory to work proper, please install DIMMs in pairs)

1 CPU &

2 DIMMs

CPU1

P1-DIMMA1/P1-DIMMB1

1 CPU &

4 DIMMs

CPU1

P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

2 CPUs &

2 DIMMs

CPU1 + CPU2

P1-DIMMA1, P2-DIMME1

2 CPUs &

4 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

2 CPUs &

6 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1

2 CPUs &

8 DIMMs

CPU1 + CPU2

P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-

DIMMG1/P2-DIMMH1

Notes:

1866 MHz memory speed is dependent on Intel E5-2600v2 CPUs.

For Intel E5-2600(v2) processor support, BIOS version 3.0 or above is
required.

Summary of Contents for X9DRD-iF




















































































































Search results

Summary of Contents for X9DRD-iF

Reviews:

Related manuals for X9DRD-iF

Brands by name

Popular brands

Supermicro X9DRD-iF, User Manual

Search results

Summary of Contents for X9DRD-iF

Reviews:

Related manuals for X9DRD-iF

Brands by name

Popular brands