Supermicro SuperStorageSystem SSG-2028R-DN2R48L, User Manual

Page: 40 / 85

Chapter 5: Advanced Motherboard Setup
5-15 5-14
SUPERSTORAGESYSTEM SSG-2028R-DN2R48L User's Manual
X10DSN-TS Jumpers
Jumper Description Default Setting
JBT1 Clear CMOS/Reset BIOS Configuration See Section 5-9 for details.
JPB1 BMC Enable Pins 1-2 (Enabled)
JPG1 VGA Enable Pins 1-2 (Enabled)
JPL1 LAN1/LAN2 Enable Pins 1-2 (Enabled)
JPME2 Manufacture (ME) Mode Select Pins 1-2 (Normal)
X10DSN-TS Connectors
Connectors Description
Battery (JBAT1) Onboard CMOS battery (see Section 5-13 for details)
FAN1/FAN2 CPU/system fan headers (Fan 1/Fan 2)
JSD1/JSD2 SATA DOM (Device on Module) power connectors 1/2
JSIOM SMCI-proprietary I/O module for add-on card use
SXB CPU2 PCI-E 3.0 x16 + CPU2 PCI-E 3.0 x8 slot
JTPM1 TPM (Trusted Platform Module)/Port 80 header
LAN1/LAN2 10_Gigabit (T) Ethernet LAN ports 1/2 on the I/O back panel
S-SATA 0/1 S-SATA 3.0 connections (0/1) supported by Intel PCH w/support of SMCI
SuperDOM w/power pins built-in)
(BP) USB 0/1 (3.0) Backpanel USB 3.0 ports 0/1
USB 2 (3.0) Type A USB 3.0 connection header for front access (USB 2)
VGA (JVGA1) VGA connection header
X10DSN-TS Onboard LED Indicators
LED Description State Status
LEDH (Top LED) BMC Heartbeat LED Green: Blinking BMC Normal
LEDL (Bottom LED) System Heartbeat LED Green: Blinking System Normal
5-8 Connector Definitions
Universal Serial Bus (USB)
Two USB 3.0 ports (USB 0/1) are located
on the I/O backpanel. In addition, a Type
A USB connector (USB 2), located close
to USB 0/1 ports, also provides USB 3.0
support for front access. (Cables are not
included.) See the table on the right for
pin definitions.
LAN Port 1/LAN Port 2
Two 10_Gigabit Ethernet LAN ports (LAN1, LAN2) are located on the I/O backplane
on the motherboard. Both ports accept RJ45 type cables. Please refer to the LED
Indicator Section for LAN LED information.
Back Panel USB 0/1 (3.0)
Type A USB 2 (3.0)
Pin Definitions
Pin# Description
1 VBUS
2 D-
3 D+
4 Ground
5 SSRX-
6 SSRX+
7 GND_DRAIN
8 SSTX-
9 SSTX+
Fan Header
Pin Definitions
Pin# Definition
1 Ground
2 +12V
3 Tachometer
4 PWR Modulation
Fan Headers
There are two 4-pin system/CPU
fan headers (FAN1/FAN2) on the
motherboard. These fans headers are
backward-compatible with the traditional
3-pin fans. However, fan speed control is
available for 4-pin fans only by Thermal
Management via IPMI 2.0. See the table
on the right for pin definitions.
Video Connection
A Video (VGA) port is located next to the PCH chip on the motherboard. Refer to
the board layout below for the location.