Supermicro SuperServer SYS-240P-TNRT User Manual Download Page 51

Page: 51 / 123

Chapter 3: Maintenance and Component Installation

Air Shroud for Power

One additional air shroud is used to cool the power supply connection area in the system

(see figure below).

Caution:

DO NOT perform this service with the system mounted inside the rack.

1. Power down the system as described in Section 3.1.

2. Remove the system from the rack and place it on a bench, then remove the cover as

described

previously

3. Place the air shroud over the power supply connectors and secure with the screws and

double-sided tape included with the air shroud, as illustrated below.

4. Close the cover and push the system back into the rack.

Figure 3-10. Installing Air Shrouds for the Power Connections

Caution:

The handles used for pulling the system from the rack are not intended to be used

to pick up or lift the system.

Summary of Contents for SuperServer SYS-240P-TNRT




























































































































Search results

Summary of Contents for SuperServer SYS-240P-TNRT

Reviews:

Related manuals for SuperServer SYS-240P-TNRT

Brands by name

Popular brands

Supermicro SuperServer SYS-240P-TNRT, User Manual

Search results

Summary of Contents for SuperServer SYS-240P-TNRT

Reviews:

Related manuals for SuperServer SYS-240P-TNRT

Brands by name

Popular brands