Supermicro SuperServer SYS-2049U-TR4 User Manual Download Page 11

Page: 11 / 151

Chapter 1: Introduction

Front Chassis Features

Item

Feature

Description

Control Panel

Control panel for the server. See Section 1.4 for details.

Hard Drive Carriers

Hot-swap hard drive carriers for HDD or NVMe drives

Figure 1-2. Chassis Front View

Information LED

Status

Description

Continuously on and red

An overheat condition has occured.
(This may be caused by cable congestion.)

Blinking red (1Hz)

Fan failure, check for an inoperative fan.

Solid blue

Local UID has been activated. Use this function to
locate the server in a rackmount environment.

Blinking blue

Remote UID is on. Use this function to identify the
server from a remote location.

Front Features

The CSE-218UTS-R1K62P is a 2U chassis See the illustration below for the features included
on the front of the chassis.

Summary of Contents for SuperServer SYS-2049U-TR4
























































































































































Search results

Summary of Contents for SuperServer SYS-2049U-TR4

Reviews:

Related manuals for SuperServer SYS-2049U-TR4

Brands by name

Popular brands

Supermicro SuperServer SYS-2049U-TR4, User Manual

Search results

Summary of Contents for SuperServer SYS-2049U-TR4

Reviews:

Related manuals for SuperServer SYS-2049U-TR4

Brands by name

Popular brands