Supermicro SuperServer E403-9D-14CN-FRDN13+ User Manual Download Page 50

Page: 50 / 136

SuperServer E403-9D-4C/14CN/16C- User's Manual

LAN Ports

The motherboard has 13 LAN ports. LAN1 – LAN9 are 1G ports and LAN10 - LAN13 are

10G SFP+ ports. In addition to the LAN ports, the motherboard offers a dedicated IPMI LAN
port. Refer to the table below for the pin definitions.

LAN Port

Pin Definition

Pin#

Definition

Pin#

Definition

TX_D1+

BI_D3-

TX_D1-

RX_D2-

RX_D2+

BI_D4+

BI_D3+

BI_D4-

COM Port/Header

The motherboard has one COM port on the I/O front panel and one COM header on the
motherboard to provide serial connections.

COM Port

Pin Definitions

Pin#

Definition

Pin#

Definition

SP_DCDA

SP_DSRA

SP_RXDA

SP_RTSA

SP_TXDA

SP_STSA

SP_DTRA

SP_RIA

GND

RJ45 Port

Pin Definitions

Pin#

Definition

Pin#

Definition

RTS

RXD

DTR

DSR

TXD

CTS

GND

Summary of Contents for SuperServer E403-9D-14CN-FRDN13+









































































































































Search results

Summary of Contents for SuperServer E403-9D-14CN-FRDN13+

Reviews:

Brands by name

Popular brands

Supermicro SuperServer E403-9D-14CN-FRDN13+, User Manual

Search results

Summary of Contents for SuperServer E403-9D-14CN-FRDN13+

Reviews:

Brands by name

Popular brands