Supermicro SUPERSERVER 4029GP-TVRT User Manual Download Page 106

Page: 106 / 147

SuperServer 4029GP-TVRT User's Manual

106

6.7 Boot

Use this tab page to configure

Boot Settings.

Boot Mode Select

Use this feature to select the type of devices to be used for system boot. The options are

Legacy, UEFI (Unified Extensible Firmware Interface), and

Dual.

Legacy to EFI Support

Select Enabled for the system to boot from an EFI OS when the Legacy OS fails. The options
are Enabled and

Disabled

Fixed Boot Order Priorities

This feature prioritizes the order of a bootable device from which the system will boot. Press
<Enter> on each entry from top to bottom to select devices.

*When the item above -"Boot Mode Select" is set to Dual (default), the following items

will be displayed for configuration:

•

Boot Option #1 - Boot Option #17

*When the item above -"Boot Mode Select" is set to Legacy, the following items will

be display for configuration:

•

Boot Option #1 - Boot Option #8

Summary of Contents for SUPERSERVER 4029GP-TVRT




















































































































































Search results

Summary of Contents for SUPERSERVER 4029GP-TVRT

Reviews:

Related manuals for SUPERSERVER 4029GP-TVRT

Brands by name

Popular brands

Supermicro SUPERSERVER 4029GP-TVRT, User Manual

Search results

Summary of Contents for SUPERSERVER 4029GP-TVRT

Reviews:

Related manuals for SUPERSERVER 4029GP-TVRT

Brands by name

Popular brands