manualshive.com logo in svg

Supermicro SC809T-780B, User Manual

Share
Download
Supermicro SC809T-780B User Manual Download Page 29

5-7

Chapter 5 Chassis Setup and Maintenance

Installing Add-on Cards:

Disconnect the power supply, lay the chassis on a flat surface, and open the 

1. 

chassis cover.

Pull open the add-on card slot clip in the rear of the chassis.

2. 

Slide the temporary add-on card "L" bracket toward the slot clip and remove 

3. 

the temporary bracket from the chassis. 

Connect the cables between the motherboard, backplane, chassis, front 

8. 

panel, and power supply, as needed. Also, fans may be temporarily removed 
to allow access to the backplane ports.

Replace the add-on card bracket and secure the bracket with a screw.

9. 

Add-on Card/Expansion Slot Setup

SC809 chassis includes I/O slots for add-on cards and expansion cards. Each side 

supports one low profile/half-length add-on card, for a total of two per system.

Add-on Card Slot Clip

Temporary "L" Bracket

Figure 5-6: I/O Shield Placement

Summary of Contents for SC809T-780B





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands