background image

 

object during an Open or Close Cycle, serious personal injury, death and/or property/product damage may occur 

 

 

 

Right hand installation shown (inside garage looking out) Fig. 1 

Check that there is sufficient side clearance to fit the operator unit. It may be fitted to either the 
right or left hand side. (fig. 1) 

 
Minimum side clearance: 
The minimum side clearance between door 
curtain and the inside edge of mounting 
bracket is 85mm; 
The minimum side clearance between door 
curtain and the outside edge of mounting 
bracket is 135mm. (fig. 2) 

 

 

FIXING OF DOOR CURTAIN TO DRUM 
WHEEL

 

The door curtain must be secured to the drum wheel 
with suitable fasteners. 
With the door in the fully closed position, mark 
the curtain at points (A) and (B)

 

 
 
 
CHECK OPERATION OF THE DOOR 

 

Before beginning the installation of the Opener, check 
the operation of the door. The door must be well 
balanced and operate smoothly and freely. When 
opened to between 900~1200mm from the floor and 
released, the door should remain in one fixed position 
and not rise or fall. The door should not bind or stick in 
the guide tracks. The ideal operational effort, required 
to open or close the door, should not exceed a force of 
10kg. 

Superlift does not recommend the 

installation of an Automatic Opener to a badly 
worn or damaged door. 

INSTALLATION INSTRUCTIONS 

Fig. 2 

Fig. 3 

Summary of Contents for RDO-5












Reviews: