Superior VINYL PERGOLA Installation Manual Download Page 1

VINYL PERGOLA

SuperiorPlasticProducts.com

Structural

Recommended Tools

•  Safety Glasses

•  Tape Measure & Level

•  Power Drill w/ (

1/8"

1/4"

5/8"

) bits

•  Hammer Drill w/ (

1/8")

 bit

•  Circular Saw w/ Fine Tooth Blade

•  Rubber Mallet

•  Ladder

What's Included 

•  Vinyl Columns 

•  Column Mounts w/ Leveling Plates

•  Vinyl Beams w/ Aluminum Channels

•  Beam Mounts

•  Rafters 

•  Vinyl Trim sets

•  All fastening hardware except concrete 

bolts/ screws (

sold separately

)

SPPIG180928

SuperiorPlasticProducts.com

•  These directions are only a guide and may not address every situation. 

•  Always wear proper safety equipment while assembling and installing. 

•  The installer should obtain all required building permits and follow all installation procedures in accordance 

with applicable building code requirements. 

•  Superior Plastic Products, Inc. shall not be held liable for improper or unsafe installations.

•  Applying paint, will void your warranty. 

•  To ensure proper coverage by our warranty please visit our website and complete the warranty form and mail 

to: Superior Plastic Products, Inc., 260 Jalyn Drive, New Holland, PA 17557

WARNING: This product can expose you to chemicals including Quartz (crystalline silica), which is known to 

the State of California to cause cancer, and Hexavalent Chromium, which is known to the State of California to 

cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Summary of Contents for VINYL PERGOLA










Reviews: