background image

4

SUPERIOR

®

 DIRECT-VENT GAS FIREPLACES • MODELS SLDVT-30/35/40/45 • CARE AND OPERATION INSTRUCTIONS

Important Safety Information

1. WARNING: Do not operate appliance with the glass front 

removed, cracked or broken. Replacement of the glass 
should be done by a licensed or qualified service person . 

2. Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician to inspect 
the appliance and to replace any part of the control system 
and any gas control which has been under water.

3. Due to high temperatures, the appliance should be located 

out of traffic and away from furniture and draperies.

4. Children and adults should be alerted to the hazards of 

high surface temperature and should stay away to avoid 
burns or clothing ignition. 

5. Clothing or other flammable material should not be placed 

on or near the appliance.

6. Young children should be carefully supervised when they 

are in the same room as the appliance. Toddlers, young 
children, and others may be susceptible to accidental 
contact burns. A physical barrier is recommended if there 
are at-risk individuals in the house. To restrict access to a 
fireplace or stove, install an adjustable safety gate to keep 
toddlers, young children, and other at-risk individuals out 
of the room and away from hot surfaces.

7. Any safety screen or guard removed for servicing an 

appliance must be replaced prior to operating the 
appliance.

8. Installation and repair should be done by a qualified 

service person. The appliance should be inspected 
before use and at least annually by a professional service 
person. More frequent cleaning may be required due to 
excessive lint from carpeting, bedding material, et cetera. 
It is imperative that control compartments, burners, and 
circulating air passageways of the appliance be kept 
clean. See maintenance instructions on page 10.

L'information de sûreté importante

1.  AVERTISSEMENT. Ne pas utiliser l’appareil si le panneau frontal 

en verre n’est pas en place, est craqué ou brisé. Confiez le 

remplacement du panneau à un technicien agréé 

2.  Ne pas utiliser cet appareil s’il a été plongé, même partiellement, 

dans l’eau. Appeler un technicien qualifié pour inspecter 

l’appareil et remplacer toute partie du système de commande  

et toute commande qui a été plongée dans l’eau.

3.  En raison des températures élevées, l’appareil devrait être 

installé dans un endroit où il y a peu de circulation et loin du 

mobilier et des tentures.

4.  Les enfants et les adultes devraient être informés des dangers 

que posent les températures de surface élevées et se tenir à 

distance afin d’éviter des brûlures ou que leurs vêtements ne 

s’enflamment.

5.  On ne devrait pas placer de vêtements ni d’autres matières 

inflammables sur l’appareil ni à proximité.

6.  Les jeunes enfants devraient être surveillés étroitement lorsqu’ils 

se trouvent dans la même pièce que l’appareil. Les tout petits, 

les jeunes enfants ou les adultes peuvent subir des brûlures s’ils 

viennent en contact avec la surface chaude. Il est recommandé 

d’installer une barrière physique si des personnes à risques 

habitent la maison. Pour empêcher l’accès à un foyer ou à un 

poêle, installez une barrière de sécurité ; cette mesure empêchera 

les tout petits, les jeunes enfants et toute autre personne à risque 

d’avoir accès à la pièce et aux surfaces chaudes.

7.  Tout écran ou protecteur retiré pour permettre l’entretien de 

l’appareil doit être remis en place avant de mettre l’appareil en 

marche.

8.  L’installation et la réparation devrait être confiées à un technicien 

qualifié. L’appareil devrait faire l’objet d’une inspection par un 

technicien professionnel avant d’être utilisé et au moins une 

fois l’an par la suite. Des nettoyages plus fréquents peuvent 

être nécessaires si les tapis, la literie, et cetera produisent 

une quantité importante de poussière. Il est essentiel que les 

compartiments abritant les commandes, les brûleurs et les 

conduits de circulation d’air de l’appareil soient tenus propres. 

Voyez les instructions d’entretien à la page 10.

[SPANISH]

Información importante de seguridad

1.  ADVERTENCIA: No opere el artefacto con el frente de vidrio quitado, 

agrietado o roto. Un técnico de servicio licenciado o capacitado 

debe reemplazar el vidrio. 

2.  No use este artefacto si alguna de sus partes ha estado bajo agua. 

Llame de inmediato a un técnico de servicio calificado para que 

inspeccione el artefacto y reemplace cualquier parte del sistema  

de control y cualquier control de gas que haya estado bajo agua.

3.  Debido a las altas temperaturas, el artefacto debe situarse fuera  

de las áreas de tráfico y lejos del mobiliario y cortinas.

4.  Se debe alertar a los niños y adultos sobre los peligros de  

las altas temperaturas en la superficie y que se mantengan  

alejados para evitar quemaduras o ignición de la ropa. 

5.  No debe colocarse ropa u otros materiales inflamables  

sobre y cerca del artefacto.

6.  Se debe supervisar de cerca a los niños cuando estén en el mismo 

cuarto que el artefacto. Los niños pequeños, los jóvenes y otras 

personas pueden ser susceptibles a quemaduras por contacto 

accidental. Se recomienda instalar una barrera física si hay 

personas en riesgo en la casa. Para restringir el acceso a una 

chimenea o estufa, instale una puerta de seguridad ajustable  

para mantener a los niños pequeños, jóvenes y otras personas  

en riesgo fuera del cuarto y lejos de las superficies calientes.

7.  Cualquier malla o resguardo de seguridad quitado para dar servicio 

a un artefacto, debe reinstalarse antes de operar el artefacto.

8.  Una persona de servicio competente debe realizar la instalación y 

reparación. Una persona de servicio profesional debe inspeccionar 

el artefacto antes de usar al menos una vez por año. Se puede 

requerir limpieza más frecuente debido a la pelusa excesiva 

del alfombrado, del material de cobijas, etc. Es imprescindible 

mantener limpios los compartimientos de control, los quemadores 

y los pasajes de circulación del aire del artefacto. Ver las 

instrucciones de mantenimiento en la página 10.

Summary of Contents for SLDVT-30NM































Reviews: