background image

40

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

WARRANTY INFORMATION

Your gas appliance is covered by a 

limited twenty-year warranty. You will 

find a copy of the warranty accompanying 

this manual.  Please read the warranty to 

be familiar with its coverage.

Retain this manual. File it with your other 

documents for future reference.

Failure to comply with the installation 

and operating instructions provided 

will result in an improperly installed 

and operating appliance, voiding its 

warranty.

Do not attempt to alter or modify the 

construction of the appliance or its com-

ponents. Any modification or alteration 

may void the warranty, certification, and 

listings of this unit.

Turn off gas and electrical power to the 

fireplace and allow it to cool before 

cleaning or servicing the appliance.
The vent termination is hot while in 

operation and for a period of time fol-

lowing the use of the fireplace. Young 

children should be carefully supervised 

when they are in the same area as a hot 

termination.

APPLIANCE OPERATION NOTICES

Do not operate appliance with the glass 

front removed, cracked, or broken.
These fireplaces are vented gas appli-

ances. Do not burn wood or other 

material in these appliances.
This appliance is only for use with the 

type of gas indicated on rating plate. This 

appliance is not convertible for use with 

other gases, unless a certified kit is used.
Cet appareil doit être utilisé uniquement 

avec les types de gaz indiqués sur la 

plaque signalétique. Ne pas l’utiliser 

avec d’autres gaz sauf si un kit de 

conversion certifié est installé.
These appliances are designed to operate 

on natural gas or propane gas only. The 

use of other fuels or combinations of 

fuels will degrade the performance of this 

system and may be dangerous.
Provide adequate clearances around 

air openings and adequate accessibility 

clearance for service and proper opera-

tion. Never obstruct the front openings 

of the appliance.
Do not use this appliance if any part has 

been under water. Immediately call a 

qualified service technician to inspect 

the appliance and to replace any part of 

the control system and any gas control 

that has been under water.
These fireplaces are designed as supple-

mental heaters. Therefore, it is advisable 

to have an alternate primary heat source 

when installed in a dwelling.
CAUTION: Hot while in operation. Do not 

touch. Severe Burns may result. Keep 

children, clothing furniture, gasoline 

and other liquids having flammable 

vapors away.
ATTENTION : L’appareil est chaud 

lorsqu’il fonctionne. Ne pas toucher 

l’appareil. Risque de brûlures graves. 

Surveiller les enfants. Garder les 

vêtements, les meubles, l’essence ou 

autres liquides produisant des vapeur 

inflammables loin de l’appareil.

APPLIANCE INSTALLATION, SERVICE, 

AND MAINTENANCE NOTICES

WARNING: Improper installation, 

adjustment, alteration, service or 

maintenance can cause injury or 

property damage. Refer to the owner’s 

information manual provided with this 

appliance. For assistance or additional 

information consult a qualified installer, 

service agency or the gas supplier.

AVERTISSEMENT : Une installation, un 

réglage, une modification, une réparation 

ou un entretien mal effectué peut causer 

des dommages matériels ou des 

blessures. Voir la notice de l’utilisateur 

qui accompgne l’appareil. Pour de l’aide 

ou des renseignements supplémentaires, 

consultez un installateur, un technicien 

agréé ou le fournisseur de gaz.

Only trim kit(s) supplied by the manufac-

turer shall be used in the installation of 

this appliance.

Seules les trousses de garniture fournies 

par le fabricant doivent être utilisées 

pour l’installation de cet appareil.

These appliances must not be connected 

to a chimney or flue serving a separate 

solid fuel burning appliance.

Any change to this appliance and/or 

its operating controls is dangerous. 

Improper installation or use of this 

appliance can cause serious injury or 

death from fire, burns, explosion or 

carbon monoxide poisoning.

CARBON MONOXIDE POISONING: Early 

signs of carbon monoxide poisoning are 

similar to the flu with headaches, dizzi-

ness and/or nausea. If you have these 

signs, obtain fresh air immediately. 

Turn off the gas supply to the appliance 

and have it serviced by a qualified 

professional, as it may not be operating 

correctly. Some people are more 

affected by carbon monoxide than others, 

including pregnant women, people with 

heart or lung disease or anemia, those 

under the influence of alcohol, and those 

at high altitudes.

GENERAL INFORMATION

The fireplace models covered in this manual 

are direct-vent sealed combustion gas fireplace 

heaters designed for residential application.  

These direct-vent appliances operate with the 

combustion chamber completely isolated from 

the indoor environment.  

All air for combustion is brought in from the 

outside and  exhaust gases are vented through 

the same direct-vent, co-axial (intake/exhaust) 

vent system.

The 

Millivolt

 appliances have a millivolt gas 

control valve with piezo ignition system. If any 

optional accessories which require electrical 

power are being installed, the electrical power 

must be provided at the time of appliance 

installation.

The 

Electronic

 appliances are designed to 

operate on either natural or propane gas. An 

electronic intermittent pilot system provides 

safe, efficient operation. External electrical 

power is required to operate these units.

Installation and Operation Instructions

900357-00, 06/2015

Innovative Hearth Products
Superior

TM

 DRT40 Direct Vent Gas Fireplace

Summary of Contents for DRT4040DEN

































































Reviews: