background image

Series AA250 

Page 1 

 LT252 Oct 2019 

Installation, Operation and Service Instructions 

 

WARM AIR HEATER 

 

 

 

Series AA250 

 

 

WARNING

 

 

FOR YOUR SAFETY

 

 

Improper installation, adjustment, alteration, service 

or maintenance can cause property damage, injury 

or death. Read the installation, operation and 

maintenance instructions thoroughly before 

installing or servicing this equipment. 

   

Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any other 

appliance. 

If you smell gas: 

1. Open windows 

2. Don’t touch electrical switches 

3. Extinguish any open flame 

4. Immediately call your gas supplier 

OWNER

 

 

INSTALLER

 

Retain this Manual & ensure available for service. 

Improper installation, adjustment, alteration, service 

or maintenance can cause injury, death or property 

damage.  

Read the installation, operation and service 

instructions thoroughly before installing or servicing 

this equipment 

  Provide Manual to Owner upon completion of 

installation! 

Read and thoroughly understand these Instructions 

before attempting any installation 

 

              Canada: 

563 Barton Street, Stoney Creek, Ontario L8E 5S1

 

              USA

: 315 N Madison Street, Fortville, IN 46040

 

www.superiorradiant.com

Summary of Contents for AA250 Series



























Reviews: