3
©
2015 Focal Point Fires plc.
QUANTITY
DESCRIPTION
1
Stove and heater assembly
1
User instruction booklet
5.0 COMPONENT CHECKLIST
Read all the instructions before continuing to unpack or install this appliance. Carefully lift the appliance from the carton. Check
that the contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling
centre.
4.0 UNPACKING THE APPLIANCE
Check that the fan outlet is not covered or obstructed in any
way, and ensure the power to the fire is switched on.
The appliance controls are concealed behind a panel on the front
of the heater.
Switch ‘e’ turns on the flame effect. Knob ‘f’ controls the brightness of the flame effect. Turn knob ‘f’ until the desired effect is
achieved.
Switch ‘b’ controls the fan function. The fan may be operated without heat, or without the flame effect. With the fan running, switch
‘c’ turns on heat setting 1 (900W), and switch ‘'d' controls heat setting 2 (1800W). The fan must be switched on for the heat set-
tings to work. The fan and heating functions can be operated with or without the flame effect. The appliance is fitted with a ther-
mostat. To adjust the thermostat, turn knob ‘a’ until the desired room temperature is achieved.
6.0 OPERATING THE APPLIANCE
‘a’
‘b’
‘c’
‘d’
‘e’
‘f’
‘a’
Thermostat
‘b’
Fan (without heat)
‘c’
Heat 900W
‘d’
Heat 900W
‘e’
Flame effect on/off
‘f’
Flame effect dimmer
2.0 INSTALLATION REQUIREMENTS
3.0 APPLIANCE DATA
Supply Voltage and rating power : 220-240V AC 50Hz, 1650 - 1850W
Fuse Rating :
13 Amp
Heating Elements :
2 x 900W
Lighting :
2 x G9 25W bulb
Location :
Indoor use only
Supply plug/cord : BS1363/1.6 metres length
The appliance is supplied with a pre-wired three pin BS1363 plug (13Amp fuse rated) and 1.6 metres of electrical flex. It is therefore
necessary for a suitable electrical socket to be located within this distance of the appliance and be easily accessible. The stove may be
installed on a combustible or non-combustible floor, however the heater outlet is underneath the stove and certain types of floor cov-
ering may be affected by the heat produced by the stove. The ability of the floor covering to withstand the heat produced by the stove
should be ascertained before proceeding with the installation of the stove. If in doubt then the stove should be mounted on a non-com-
bustible hearth or plinth which extends for at least 150mm in front of the stove.This appliance should be positioned on a firm level sur-
face. If the stove is to be sited in a fire surround then the suitability of the surround for use with electrical heaters should be estab-
lished with the fire surround manufacturer.If fitted into an open draught fireplace, it is advisable to block off the chimney to reduce the
risk of draught through the stove which may cause the safety cut out system in the fan heater to operate.
• DO NOT run the mains cable under carpets, rugs etc.
• DO NOT cover or obstruct the heater in any way. Overheating will result if it is acci-
dentally covered.
• Never immerse the product in water or any other liquids.
• DO NOT use the appliance outdoors.
• Before cleaning the appliance, ensure it is unplugged from the power and that it is com-
pletely cool.
• DO NOT clean the appliance with abrasive chemicals.
• Never use accessories that are not recommended or supplied by the manufacturer. It
could cause danger to the user or damage to the appliance.
• DO NOT insert or allow foreign objects to enter the inlet or outlet vents as this may
result in electric shock, fire or damage to the appliance.
• DO NOT install the fire using an extension cord.
• Unplug from the mains supply if the appliance is not to be used for long periods.
1.0 IMPORTANT NOTES - CONTINUED
GB IE
