KIT CONTENTS
• STILETTO PRO
• USB-TO-MICRO USB cable
• T8 Torx Wrench
FUEL GAUGE
The STILETTO PRO is equipped with a LED that displays the battery status, both during use and while charging.
CHARGING THE STILETTO PRO
The STILETTO PRO is powered by an integral lithium polymer (LiPo) battery (950 mAh).
The STILETTO PRO’s MICRO USB port is for charging input only (Standard 5V, 500 mA).
How to charge the LiPo rechargeable battery:
1. Insert the MICRO USB cable plug into STILETTO PRO charging port.
2. Insert USB cable plug into a USB port of a computer or another device that will provide
power to the STILETTO PRO.
3. When the fuel gauge turns green, the STILETTO PRO is charged to more than
95% of battery capacity.
NOTE: The SureFire FIREPAK™ and GUARDIAN
®
will charge the STILETTO PRO approximately
two times.
NOTE: Charging a fully depleted battery can take up to three hours. The light may be left plugged into
the charger without damaging the battery.
NOTE: When the STILETTO PRO is being charged and the temperature is too cold (Below 32°F/0°C)
or too hot (Above 120°F/50°C), the fuel gauge will blink yellow which indicates charging stopped.
Once the temperature reaches 41°F/5°C or 113°F/45°C, it will continue charging. When the battery
is drained below 3.0V, the STILETTO PRO has a pre-charge mode when connected to a charger. The
Fuel Gauge will blink red rapidly until the battery reaches 3.1V. Once the battery has a minimum of
3.1V, the Fuel Gauge conditions above will apply.
LIGHT OPERATION - PROFILE CONFIGURATION
PRIMARY switch: activates the light in the various outputs
PROGRAMMING switch: see “HOW TO CHANGE PRIMARY AND TACTICAL MODES”
TACTICAL switch: for momentary, strobe or constant-on output
Primary Switch Activation
Mode 1 (Default): Press the PRIMARY switch to cycle from LOW to MEDIUM to HIGH to OFF. The cycle
will repeat if the PRIMARY switch is pressed within two seconds. If the STILETTO PRO is activated on
either LOW, MEDIUM or HIGH and the PRIMARY switch has not been pressed within two seconds,
the next press shuts the light OFF. The last used output is not remembered.
Mode 2: Same as above, but with the cycle changed to HIGH to MEDIUM to LOW to OFF.
Tactical Switch Activation
Mode 1 (Default ; TACTICAL & STROBE): Press and hold the TACTICAL switch for HIGH only; release
the switch to shut OFF. For STROBE, rapidly tap the TACTICAL switch three or more times and hold
down on the 3rd+ press. Release the switch to shut the STROBE OFF.
Mode 2 (Constant-on): Press the TACTICAL switch for constant-on in HIGH only. When the switch is
pressed again, the light will shut OFF.
EMERGENCY MODE Activation
Press and hold the PROGRAMMING switch for five seconds or more to activate the MEDIUM frequency,
MEDIUM output STROBE. Press the PRIMARY or TACTICAL switch to shut EMERGENCY MODE OFF.
HOW TO CHANGE PRIMARY AND TACTICAL MODES
The PROGRAMMING switch is used to select the behavior of the PRIMARY and TACTICAL
output buttons. The STILETTO must be off to change modes. The PRIMARY and TACTICAL
switches are changed independently (Ex: PRIMARY switch can be on MODE 1 and TACTICAL
switch can be on MODE 2.)
Changing the modes for either the PRIMARY or TACTICAL switches:
Step 1: Press and hold the PROGRAMMING switch for two to five seconds. The Fuel Gauge
LED will illuminate BLUE to indicate programming mode.
Step 2: While holding the PROGRAMMING switch and observing the BLUE LED Fuel
Gauge, tap either the PRIMARY or TACTICAL switch once and release the
PROGRAMMING switch. Pressing the PRIMARY or TACTICAL switch more than
ONCE exits the programming mode. Once the PROGRAMMING switch is released,
the Fuel Gauge LED blinks GREEN three times for success or RED three times for error.
POCKET CLIP RELOCATION
1. Rotate T8 Torx screws counter clockwise with supplied wrench to remove the
two pocket clip screws.
2. Place pocket clip on STILETTO PRO body in desired position.
3. Rotate T8 Torx screws clockwise with supplied wrench. Tighten screws to 1.4 inch pounds of
torque. If torque wrench is not available, tighten screws an additional 1/4 turn once resistance
is felt. DO NOT OVERTIGHTEN. The STILETTO PRO body is die cast aluminum. If the screws are
overtightened, the screw holes can become stripped, which could void the warranty.
FUEL GAUGE LED INDICATOR
CHARGING
DISCHARGING
SOLID GREEN
100% Charged, Max Capacity
95-100% Charged
SOLID YELLOW
Charging, Medium Capacity Battery Charge Low (reduce light
output level or recharge)
SOLID RED
Charging, Low Capacity
Recharge Immediately
FLASHING RED
Pre-charge mode
Battery Critically Low
PRIMARY
SWITCH
MICRO-USB
PROGRAMMING
SWITCH
FUEL GAUGE LED
TACTICAL
SWITCH
STROBE WARNING
Exposure to strobing lights may cause dizziness, disorientation, and nausea. A very small
percentage of people suffer from photosensitive epilepsy—approximately .00025% of the
population—and may experience seizures or blackouts triggered by strobing lights. Visit www.
epilepsyfoundation.org for more information about this rare form of epilesesy. Anyone who has
had symptoms linked to this condition should consult a doctor before using this product.
To Disable Lockout Mode:
1. Press the PRIMARY and TACTICAL switch simultaneously, then release.
NOTE: The PRIMARY, TACTICAL and PROGRAMMING switches will be instantly ready for use when
Lockout Mode is disabled.
To Enable Lockout Mode
1. Press and hold the PRIMARY and TACTICAL switch simultaneously for two seconds, then release.
2. The green Fuel Gauge LED will blink twice to confirm Lockout Mode is enabled.
NOTE: The PRIMARY, TACTICAL and PROGRAMMING switches will not activate the STILETTO PRO
when Lockout Mode is enabled.
LOCKOUT MODE