Page 7 of 12 Form 0134E 06/06/2004
Superchips Inc.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 (407) 585-7000 http://www.Superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Press ‘YES’ to make changes to the Custom Option Settings.
Press ‘NO’ to bypass the Custom Options and go directly to
Viewing the Option
Settings
at Step 6 that follows.
Adjust = < or >
Save = YES
Press Any Key
to Continue
Pressing ‘<’ and ‘>’ on the keypad adjusts the Custom Option setting.
Pressing ‘YES’ on the keypad saves the Custom Option setting.
Editing the Tire Height Option Setting
The Tire Height Option allows the user to correct the Speedometer/Odometer when tires
other than stock size are installed. The Tire Height Option allows the user to set the Tire
Height to STOCK or to 24.0 - 38.0 inches in 1/4-inch intervals. Tire height should be
measured from the top of the tire to the ground at its highest point.
The MAX MicroTuner will beep and display the message:
Adjust tire
height? YES/NO
Press ‘NO’ and the MAX MicroTuner will continue to the
Viewing the Options Settings
at Step 6.
Press ‘YES’ and the MAX MicroTuner will beep and display the keys to use while editing
the Tire Height Option setting:
Adjust = < or >
Save = YES
Press Any Key
to Continue
Pressing ‘<’ and ‘>’ on the keypad adjusts the Custom Option setting.
Pressing ‘YES’ on the keypad saves the Custom Option setting.
Press any key on the keypad to continue. The MAX MicroTuner will beep and display the
message:
Stock Hght XX.XX
(xx.xx is Stock Tire Height)
>Up <Down Yes
Press ‘<’ or ‘>’ to select the Tire Height setting. Once a tire height change has taken
place the MAX MicroTuner will display the message:
Tire Hght XX.XX
(xx.xx is Tire Height)
>Up <Down Yes
Press ‘YES’ to save the Tire Height Option setting.
6. Viewing the Options Settings
The MAX MicroTuner will beep and display the message:
View Custom
Opt? YES or NO
Press ‘YES’ to view the present Custom Option Settings.
The MAX MicroTuner will beep and display the message:
Press Any Key
to Continue...
Page 8 of 12 Form 0134E 06/06/2004
Superchips Inc.
Superchips Inc.
1790 East Airport Blvd., Sanford, FL. 32773 (407) 585-7000 http://www.Superchips.com
Superchip & Superchips are registered trademarks of Superchips, Inc.
Press any key on the MAX MicroTuner keypad. The Custom Options current settings
will be presented in order. Press any key to view the next Custom Option setting.
Press ‘NO’ to continue without viewing the Custom Option Settings.
7. Accepting the Options Settings
The MAX MicroTuner will beep and display the message:
Accept Custom
Opts? YES or NO
Press ‘NO’ to return to the
Installing the Superchips Performance Program
at Step 4.
Press ‘YES’ to accept the options and continue.
The MAX MicroTuner will beep and
display the message:
Please Wait…
After a brief wait The MAX MicroTuner will beep again and display the message:
Install Tuning?
YES or NO
Press ‘YES’ to continue with the programming process at Step 8.
Press ‘NO’ to not apply any changes to your vehicle. The MAX MicroTuner will then
continue to
End of Programming & Exit Sequence
at Step 9 to insure correct vehicle
operation.
8. Programming Section
The MAX MicroTuner will beep and display the message:
Ready to Install
New TUNING
Important! Leave
the IGNITION ON
Press ‘>’
to Continue…
Press the ‘>’ key. The MAX MicroTuner will beep and display the following message:
Install Tuning
*****
The bottom line of the display shows the programming progress. During
programming, the "Wait to Start" light will flash and that this is normal.
Once the programming sequence has been successfully accomplished on a vehicle, the
MAX MicroTuner becomes LOCKED to that vehicle. The MAX MicroTuner may not be used
to tune any other vehicle. The MAX MicroTuner may be used on other Dodge or Chrysler
vehicles as a DTC Reader.
The MAX MicroTuner will then continue to
End of Programming & Exit Sequence
at
Step 9 to insure correct vehicle operation.
IMPORTANT NOTE
Do not interrupt the MAX MicroTuner programming cycle or disconnect it from your vehicle
until the programming cycle is complete. The entire programming cycle can take several
minutes.
