Page 7 of 12
Form 0131K 10/10/2005
2609 South Sanford Ave1790 East Airport Blvd.,. Sanford, FL. 32773 (407) 585-7000
http://www.Superchips.com Ph. 888-CAR-CHIP
Superchip & Superchips are registered trademarks of Superchips, Inc.
Raise SPEED LIM?
YES or NO
The current Speed Limiter setting will flash. Use ‘<’ or ‘>’ to change the
setting and ‘YES’ to save the Speed Limiter Custom Option setting.
The MAX MicroTuner will beep and
display the message:
Please Wait…
After a brief wait The MAX MicroTuner will beep again and display the message:
Install Tuning?
YES or NO
Press ‘YES’ on the MAX MicroTuner keypad to continue with the Programming
process at Step 6.
Press ‘NO’ to return to
Selecting Tune Vehicle / Diagnostics
at Step 2.
6. Programming Section
The MAX MicroTuner will beep and display the message:
Install Tuning
The bottom line of the display shows the programming progress.
Once the programming sequence has been successfully accomplished on a vehicle, the
MAX MicroTuner becomes LOCKED to that vehicle. The MAX MicroTuner may not be used
to tune any other vehicle. The MAX MicroTuner may be used on other GM vehicles as a
DTC Reader.
7.
End of Programming Sequence
When the programming sequence is completed the MAX MicroTuner beeps and will display
the following messages:
Clearing DTC’S
Please Wait…
Tuning Installed
Turn Ign OFF
Turn the ignition OFF(LOCK), and do the following:
Press the ‘>’ Key
to Continue…
Press the ‘>’ key to continue. The MAX MicroTuner will display the following messages:
Please Wait…
Remove the 2705
MAX Tuner…
Remove the cable from the diagnostic port.
Start Vehicle
IMPORTANT NOTE
Do not interrupt the MAX MicroTuner programming cycle or disconnect it from your vehicle
until the programming cycle is complete. The entire programming cycle can take several
minutes.
Page 8 of 12
Form 0131K 10/10/2005
2609 South Sanford Ave1790 East Airport Blvd.,. Sanford, FL. 32773 (407) 585-7000
http://www.Superchips.com Ph. 888-CAR-CHIP
Superchip & Superchips are registered trademarks of Superchips, Inc.
OnStar is a registered trademark of the General Motors Corporation
8. Return to Stock Sequence
The
Return to Stock Sequence
is used to reprogram a vehicle previously tuned with the
Superchips MAX MicroTuner with its original stock tuning. Follow the steps described in
Connecting the Superchips MAX MicroTuner to Your Vehicle
at Section 1. Following the
typical start up messages, if the MAX MicroTuner has been previously used to program a
vehicle, the MAX MicroTuner will beep and display:
MicroTuner is
VIN Locked
This indicates the MAX MicroTuner has been previously used to program a vehicle. It
should not be used program another vehicle. The MAX MicroTuner will continue to operate
normally on the original vehicle.
Turn the ignition switch to the ON position. Press the ‘>’ key on the keypad. The MAX
MicroTuner will beep and display the message:
A= Tune Vehicle
B= Diagnostics
Press the ‘A’ key on the keypad to continue with the tuning process.
Press the ‘B’ key to read and/or clear any Diagnostic Trouble Codes.
If the ‘A’ key is pressed, the MAX MicroTuner will beep and display the message:
Initialization…
Please Wait…
After establishing communications, the MAX MicroTuner will display the following message:
RETURN to STOCK?
YES or NO
If ‘NO’ is pressed, the
MAX MicroTuner will return to
Installing the Superchips
Performance Program
at Step 5.
If the ‘YES’ key is pressed when the MAX MicroTuner will beep once and display the
following message:
Return To STOCK
The bottom line of the display shows the programming progress.
Important Note for 2003 and Later Ford Expeditions & Lincoln NavigatorsVehicles with
OnStar
A special procedure is required to disable the fuel system inallow programming of your
vehicle if you have OnStar. Please see Section 911 of this manual.
