Super Sealer REI-85 Operation Manual Download Page 6 | Manualshive

Page: 6 / 24

background image

Updated: 15 November, 2011 Page 6

REF: REI-85-0045

3.1 SPECIFICATIONS

REI-85

Output Capability

Air Requirement

Machine Dimension

Machine Weight

Power Requirement

Up to 15 cycles per minute

3HP (600KPa, 200~300L/M)

~ 800Lmmx1000Wmmx2000Hmm

~ 280 kg

1Phase, 220-240Vac @ 20Amps

4.

CONTROL PANEL

REI-85 Control Panel

The control panel is where some of the functions of the machine could be adjusted and/or modified based on

your specific machine requirements. Please note that the machine is delivered with predefined feature

parameters and you may not need to change any of the defined settings.

TOUCH SCREEN:

Please check from page (13) for operation detail & function setting.

ROTARY:

The switch on/off to start/stop turntable.

EMERGENCY:

Safety Button provided to STOP the machine

POWER ON/ OFF:

The power on/off switch to start/stop the operation of the machine

«
...
4
5
6
7
8
...
»

Summary of Contents for REI-85

























Reviews:

No comments

Related manuals for REI-85

Brand: N'oveen Pages: 34

Brand: FoodSaver Pages: 16

Brand: Toastmaster Pages: 2

Brand: Jata electro Pages: 28

Brand: TAIKO Pages: 21

Warmilu IncuBlanket

Brand: VIA Technologies Pages: 15

Brand: Franke Pages: 8

Brand: Anvil Pages: 1

Brand: Anvil Pages: 2

Brand: Anvil Pages: 2

thermoport 100 L

Brand: Rieber Pages: 20

Brand: inventum Pages: 32

instant warmer advanced BRZ0080

Brand: Baby Brezza Pages: 2

Brand: Monzana Pages: 10

Brand: Yeasincere Pages: 10

Brand: Broil King Pages: 2

Brand: U-Line Pages: 12

Brand: Weston Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands