1
User's manual
MODEL: SCL-BLUELOVE-B (25K)
Thank you for using the SCL-BLUELOVE-B laser projector. For the sake of safety and better operation of this
projector, please read this manual carefully before use and operate the projector, lest incur any personal injury or
damage to the projector
●
Package list:
When you unpack the case , please take time to examine the items as follow:
········
laser projector 1 pc
········
laser projector sling 1 pc
········
power
’
s cable 1 pc
········
user
’
s manual 1 pc
●
Function Introduction:.
SCL-x series laser projector adopts the semiconductor laser source.Laser generator is double-temperature -controlled
power supply. The laser light source has a long life span and highly stability, complying with the international
standard.
Laser effect: There are 128pcs latest patterns in it ; can be used for word performance, animation performance, laser
beam performance, with spatial, projection and animation effects. The scientific laser beam route design and fast laser
vibratory mirror system will announce a new era of laser lighting performance.
●
Instructions:
After unpacking, check whether the laser lighting has been damaged by transport such as any screw loosening,
lighting tube broken, etc. If everything is OK, select a proper location, hang the light and adjust its angle properly,
then connect the power cord and the ground wire before switch on at the means.
Notice that while using this laser lighting the green and yellow wire has to connect the ground properly by
professionals. Please examine the electrics and voltage before power on it. We suggest customer apply 110V/230V or
a transformer. 20 seconds after powered on the projector, it will self-check and then can be used.
Because the radiate laser generator
’
s own characteristic, securing the laser
’
s long life span. Please terminate it for
10 minutes after using it for 30 minutes. Avoid being interfered by other signals while controlled by software or using
the DMX-512 signal controller, such as wireless interphone & high radiated source.
2
●
Technical Parameters:
Rated Voltage:AC90~250V
±
10
％
Rated frequency:50Hz
～
60Hz
Laser power:400mw
Wavelength:447nm
Color:blue
Patterns:128pcs latest laser patterns
Scanning:25kpps vibratory mirror system
Scanning angle:
±
20 degrees
DMX-512:10 channels
Control mode: DMX-512 / Music active / Master & Slave
Cool system: fan
Operating environment: indoor
●
Switch code:
SCL-BLUELOVE-B laser performance system has controlled by on/off switch address code. 1 to 9 are the numerical
value DMX 512 signal, 10 is the exchange switch of DMX512 signal control and music control / automatic / master
and slave.
Control mode set up detail as bellow:
Mode
Control switch (ON)
1
Single projector controlled by
sound
1
－
9:OFF,10:ON
2
Single projector controlled by
automatic
1
－
8:OFF,9
、
10:ON
3
DMX-512
1-9:ON,10:OFF
4
Slave Mode
1-10:OFF
●
Signal Connection and Address Code Dialing:
When the controller transmits DMX512 standard signals, the connection of which is accomplished through the
“
input
”
and
“
output
”
3-pin XLR socket. When a console signal outputs to the unit, it must correspond to the Pin 1
Ground, Pin 2 Positive and Pin 3 Negative of the XLR socket on the unit. If it does not work just try exchanging the
Pin 2 and Pin 3 (these 2 pins are generally do not need exchanged for consoles). The signal wire length should not
exceed 100m in order to avoid the interference of the other signals by any other electric appliances.
This unit adopts the 3 pins XLR socket, detail connection of many units as bellow:
D M X 5 1 2
C O N T R O L L E R
IN
OUT
OUT
IN
POWER
MIC
2
OUT
IN
POWER
MIC
OUT
IN
POWER
MIC
1
*Notice:
1. You can not connect to the DMX-512 controller when the master and slave projector are operating synchronously,
otherwise the master and slave synchronous functions can
’
t be realized;
2. When operating the master and slave controlling, it must be only one master projector, otherwise it can not be
operated synchronously.
