CAUTIONS
2
CME-LX100 No.2137-00
LX-100
Make sure that the power supply is off while wiring.
Take care that wrong wiring will damage the sensor.
Verify that the supply voltage variation is within the rating.
Take care that if a voltage exceeding the rated range is applied, or if an AC
power supply is directly connected, the sensor may get burnt or damaged.
In case noise generating equipment (switching regulator, inverter mo-
tor, etc.) is used in the vicinity of this product, connect the frame ground
(F.G.) terminal of the equipment to an actual ground.
If power is supplied from a commercial switching regulator, ensure that the frame
ground (F.G.) terminal of the power supply is connected to an actual ground.
Do not use during the initial transient time (0.5 sec.) after the power
supply is switched on.
Take care that short-circuit of the load or wrong wiring may burn or damage the sensor.
Do not run the wires together with high-voltage lines or power lines or put
them in the same raceway. This can cause malfunction due to induction.
Take care that the sensor is not directly exposed to fluorescent light
from a rapid-starter lamp or a high frequency light device.
If the surface of the sensing object has a shine,
mount the sensor inclining approx. 10 to 15 degrees
against the sensing object.
Do not touch the lens of the sensor by hand directly. If
the lens becomes dirty, wipe it off with a soft cloth gently.
When the inside lens is steamed up, unscrew the
lens to get rid of the condensation.
For LX-101-
غ
-Z, be sure to use the optional cable with connector.
Extension up to total 100m is possible with 0.3mm
2
, or more, cable.
However, in order to reduce noise, make the wiring as short as possible.
This sensor is suitable for indoor use only.
Do not use this sensor in places having excessive vapor, dust, etc., or
where it may come in direct contact with water, or corrosive gas.
Take care that the product does not come in direct contact with water,
oil, grease, or organic solvents, such as, thinner, etc.
Make sure that stress by forcible bend or pulling with 76N, or more, force
is not applied directly to the sensor cable joint.
This sensor cannot be used in an environment containing inflammable
or explosive gases.
Never disassemble or modify the sensor.
INSTRUCTION MANUAL
Digital Mark Sensor
Photoelectric Sensor
Thank you very much for using SUNX products. Please read this Instruction
Manual carefully and thoroughly for the correct and optimum use of this
product. Kindly keep this manual in a convenient place for quick reference.
Never use this product as a sensing device for personnel
protection.
In case of using sensing devices for personnel protec-
tion, use products which meet standards, such as
OSHA, ANSI or IEC etc., for personnel protection ap-
plicable in each region or country.
٨
٨
WARNING
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
٨
10
䌾
15
㫦
SPECIFICATIONS
1
Notes: 1)
2)
The connector type LX-101
غ
-Z is 100mA.
The connecting cable is not supplied as an accessory for the connector type
LX-101
غ
-Z. Make sure to use the optional cables with connector below:
CN-24B-C2 (Straight type, 4-core, Cable length: 2m) CN-24BL-C2 (Elbow type, 4-core, Cable length: 2m)
CN-24B-C5 (Straight type, 4-core, Cable length: 5m) CN-24BL-C5 (Elbow type, 4-core, Cable length: 5m)
Max. sink current: 50mA
Applied voltage: 30V DC or less
(between output 2 and 0V)
Residual voltage: 1.5V or less
(at 50mA sink current)
NPN open-collector transistor
<NPN output type>
Max. source current: 50mA
Applied voltage: 30V DC or less
(between output 2 and +V)
Residual voltage: 1.5V or less
(at 50mA source current)
PNP open-collector transistor
<PNP output type>
Incorporated
Incorporated OFF-delay timer/ON-delay timer, switchable either effective or ineffective
'RUN': Green LED, 'TEACH', 'ADJ', 'COLOR', 'TIMER', 'PRO': Yellow LED
MODE indicator
Response time
Operation indicator
Mark mode: 2-level teaching/Full-auto teaching, Color mode: 1-level teaching
Sensitivity setting
Incorporated
IP67 (IEC)
4 digits red LED display
Orange LED (lights up when output 1 is ON)
Mark mode: 45
Ǵ
s or less, Color mode: 150
Ǵ
s or less
Digital display
Timer function
Protection
Fine sensitivity adjustment function
Material
Ambient temperature
120g approx.
55g approx.
Weight
Enclosure: PBT, Display: Polycarbonate, Operation buttons: Silicon rubber, Lens: Glass
0.2mm
2
5-core cabtyre cable, 2m long
Cable
35 to 85% RH, Storage: 35 to 85% RH
-10 to +55
͠
(No dew condensation or icing allowed), Storage: -20 to +70
͠
Ambient humidity
Red/green/blue LED
Emitting element
Current consumption
Teaching input
Supply voltage
Setting distance
Output 1
(OUT)
Item
Normal mode: 750mW or less (Current consumption 30mA or less at 24V supply voltage)
EOC mode: 600mW or less (Current consumption 25mA or less at 24V supply voltage)
12 to 24V DC+/-10%
˴
Ripple P-P10% or less
10mm
r
3mm
Low (ON): 0 to 2V DC
Source current 0.5mA or less
Input impedance 10k
ǡ
approx.
High (OFF): 5V to +V DC, or open
<NPN output type>
High (ON): 5V to +V DC
Sink current 0.5mA or less
Input impedance 10k
ǡ
approx.
Low (OFF): 0 to 0.6V DC, or open
<PNP output type>
Max. sink current: 50mA (Note 1)
Applied voltage: 30V DC or less
(between output 1 and 0V)
Residual voltage: 1.5V or less
㨇
at 50mA (Note 1) sink current
㨉
NPN open-collector transistor
<NPN output type>
Max. source current: 50mA (Note 1)
Applied voltage: 30V DC or less
(between output 1 and +V)
Residual voltage: 1.5V or less
㨇
at 50mA (Note 1) source current
㨉
<PNP output type>
PNP open-collector transistor
LX-101-P-Z
LX-101-P
LX-101-Z
LX-101
Connector type
Cable type
NPN output
PNP output
Type
Model
No.
Mark mode: Light-ON/Dark-ON Auto-setting method on teaching,
Color mode: Coincidence-ON/Non-coincidence-ON
Output operation
Incorporated
Short-circuit protection
Inverted operation of the output 1
Output operation
Short-circuit protection
Output 2 (Inversion output)
(OUT)
MOUNTING
3
PART DESCRIPTION
4
I/O CIRCUIT DIAGRAMS
5
Notes: 1)
2)
The output 2 is not incorporated to connector type LX-101
غ
-Z.
The current of the connector type LX-101
غ
-Z is 100mA.
NPN output type
D
2
10k
ǡ
D
1
1
4
12 to 24V DC
r
10%
Terminal No. of Connector Color code of cable type/cable with
connector
(Brown) +V
(Black) Output 1
50mA max. (Note 2)
50mA max. (Note 2)
(White) Output 2 (Note 1)
3
Z
D1
Z
D2
(Blue) 0V
T
r1
T
r2
(Pink) Teaching input
*1
5V
2
Sensor
circuit
Users' circuit
Internal circuit
Load
Load
Do not make the
sensor detect an
object in this di-
rection because it
may cause unsta-
ble operation.
Good
No good
Care must be taken regarding the
sensor mounting directrion with
respect to the object's direction of
movement.
The tightening torque should be
0.8N
䊶
m or less.
Sensor mounting
bracket
MS-LX-1
(Optional)
M4 screw with washers
COLOR
TIMER
OPE.
RUN
ADJ.
TEACH
Operation indicator
(Orange)
MODE/CANCEL key
OFF/ENTER key
ON/SELECT key
MODE indicator / RUN (Green)
MODE indicator / ADJ (Yellow)
MODE indicator / TEACH (Yellow)
MODE indicator / TIMER (Yellow)
MODE indicator / COLOR (Yellow)
MODE indicator / PRO (Yellow)
Digital display (Red)
