SunStar STARGLO Series Installation And Operation Instructions Manual Download Page 1

 

 

Form #43219020 

 

 

June 09

 

 
 
 

INSTALLATION AND OPERATION INSTRUCTIONS 

 

 

OWNER / INSTALLER: 

For your safety this manual must be carefully and thoroughly read 
and understood before installing, operating or servicing this heater. 

 

 
 

INFRARED RADIANT CERAMIC HEATER 

 

 

STARGLO SERIES

 

 

 

 

 

 

!

INSTALLER: 

This manual is the property of the owner.  Please present this manual 
to the owner   when you leave the job site. 

 

 

S

WARNING:

 Improper installation, adjustment, alteration, service, or maintenance can 

cause property damage, injury or death.  Read the installation, operation 
and maintenance instructions thoroughly before installing or servicing this 
equipment.  
 
In locations used for the storage of combustible materials, signs must be 
posted to specify the maximum permissible stacking height to maintain 
the required clearances from the heater to the combustibles. Signs must 
either be posted adjacent to the heater thermostats or in the absence of 
such thermostats, in a conspicuous location. 

 

 

!

IMPORTANT:

 

SAVE THIS MANUAL FOR FUTURE REFERENCE. 

 
 

SUNSTAR HEATING PRODUCTS, INC. 

Post Office Box 36271  

(28236)

     306 West Tremont Avenue  

(28203

)

     Charlotte, North Carolina 

Phone  (704) 372-3486 – www.sunstarheaters.com – email: [email protected]

 

 

Summary of Contents for STARGLO Series


















Reviews: