SunStar KM-957 Series User Manual Download Page 20 | Manualshive

Page: 20 / 32

SunStar KM-957 Series User Manual Download Page 20

20

[Figure 33]

[Figure 34]

11) Adjusting feed cam

⑴

The adjustment of the feed cam body

①

will determine the timing of the feed dog and the needle. Lay the machine back

and move the needle to its highest position. The standard position will be made when the baseline

②

of the feed cam

body

①

is aligned with the carved sign

③

on the bottom of the bed.

⑵

If the feed dog is faster than the needle, loosen the feed cam body fixing screw

④

and turn the feed cam body in the

arrow direction and then tighten the feed cam body fixing screw

④

.

Turn it in the opposite direction to make the feed dog faster then the needle.

12) Adjusting feed dog height

Loosen the wheel feed dog clamp screw

①

and the wheel feed dog driving gear clamp screw

②

and move the wheel feed

dog fixing plate

③

, the wheel feed dog

④

, and the wheel feed dog driving gear

⑤

so that the upper side of the wheel feed

dog

④

is protruding about 0.8mm from the needle plate top

⑥

. The clearance between the wheel feed dog

④

and the wheel

feed dog driving gear

⑤

is about 0.5mm.

«
...
18
19
20
21
22
...
»

Summary of Contents for KM-957 Series

































Reviews:

No comments