manualshive.com logo in svg

SunStar KM-341BL, User Manual

Share
Download
SunStar KM-341BL User Manual Download Page 13

13

B. Lubricant Supply to Oil Fan  

a) Fill lubricant up to “High”.  

b) Use the oil for Sunstar industrial sewing machine or Shell’s Tellus C10 as lubricant.  

c) When lubricant reaches “Low”, lubricant should be resupplied until it reaches “High”.  

d) Exchange lubricant oil every two weeks.  

[ Fig. 12 ]

Oil pump

Magnet

[ Fig. 13 ]

4-12. Inserting Bobbin into Bobbin Case  

1) Insert the bobbin into the bobbin case as in the figure below.  

※

If the bobbin is inserted in the opposite direction, it is spined loosely, causing entanglement of lower thread.  

2) Insert the thread into the lower thread tension adjusting spring

④

through the thread path

③

and take out the thread

through the thread hole

⑥

.

3) Set the output tension to the extent that when the bobbin case

①

is dropped with the end of the thread held, it falls

gradually.  

4) When the tension adjusting screw

⑤

is turned clockwise, the lower thread tension gets stronger. When it is turned counter-

clockwise, the lower thread tension gets weaker.  

[ Fig. 14 ]

Weaker

Stronger

⑤

⑥

④

③

②

①

Summary of Contents for KM-341BL























Reviews:

No comments

Brands by name

Popular brands

Load more brands