SUNPUMPS SCP series Operation And Installation Manual Download Page 17

 

BEFORE CALLING SUNPUMPS 

 
If at all possible when calling Sun Pumps for technical support there are a few things which will help to 
speed up the process and help us determine the cause of and solution to the system failure.  The best way to 
get help is to call while you are physically at the location of your pump, have good sunlight, and have a 
multimeter and a screwdriver with you.  
 
Furthermore, please fill out the form below before calling.  This information will provide us with most of 
the preliminary information we need to help you.  If you cannot physically be at the site, filling out the 
worksheet is a must. 
 
 
Pump Model Number:            ____________________ 
Pump Serial Number: 

     ____________________ 

Motor Serial Number: 

     ____________________ 

 
Controller Model Number:     ____________________ 
 

Software Version     ____________________ 

 
 
Date Purchased:                      ____________________ 
 
Solar Module Specifications:    

Model Number         ____________________ 
Rated Watts              ____________________ 
Voc                           ____________________ 
Vmp                          ____________________ 
Isc                             ____________________ 
Imp                           ____________________     

 
 
Solar Modules Connected in Series _______________ X Voc _______ = _________ Array Voc 
 
Solar Modules Connected in Series _______________ X Vmp _______ = _________ Array Vmp 
 
Series Strings Connected in Parallel_______________ X Isc _________= _________ Array Isc 
 
Series Strings Connected in Parallel_______________ X Imp _________= _________ Array Imp 
 
 

 

 
 
 
 
 

 

Summary of Contents for SCP series



















Reviews: