background image

21 

 

EXERCISE INSTRUCTIONS 

 

GETTING STARTED: 

Before starting any exercise program, you should consult your physician to determine if you have any 
medical or physical conditions that could put your health and safety at risk or prevent you from using 
the equipment properly. Be aware of your body’s signals. Incorrect or excessive exercise can damage 
your  health.  Stop  exercising  immediately  if  you  experience  any  of  the  following  symptoms:  pain, 
tightness  in  your  chest,  irregular  heartbeat,  shortness  of  breath,  lightheadedness,  dizziness,  or 
feelings of nausea. 
 
Get to know your treadmill. Before attempting to use the treadmill, take some time to stand alongside 
and familiarize yourself with the controls. Once you get on, you can stand with your feet on the side 
rails and stabilize yourself by holding onto the handrails. 
 
Next, attach the clip end of the 

Safety  Key  (No.  66)

 to your clothes and insert the magnetic end of 

the key into the computer console. Press  the START  button to start the  treadmill. The  treadmill  will 
start  at  the  system  default  setting  speed  of 

0.5  MPH

.  when  you  feel  comfortable,  you  may  slowly 

increase  this  speed.  When  you  are  finished  with  your  exercise,  press  the STOP  button  to  stop  the 
treadmill or you can remove the magnetic end of the 

Safety Key (No. 66)

 to stop the treadmill.  

 

 
 

 
 

 
 

 

 

 

 

 

 
 
 

 
 
 
 

 

 

Summary of Contents for SF-T4400
























Reviews: