background image

11

• 

Ammonia products

• 

Acid-based products

These chemicals will harm the unit and will damage  

the cleaning surface.

Shutting down

1.  Turn the switch to the OFF (0) position and unplug the 

power cord from the outlet.

2. 

Turn off the water source.

3.  Hold the trigger to release water pressure.
4.  Disconnect the garden hose from the water inlet on  

the unit.

5.  Disconnect the high-pressure hose connection on the 

trigger gun handle.

6.  Release the trigger and engage the gun safety lock.

m

WARNING! 

Turn off the water supply and squeeze the 

trigger to depressurize the unit. Failure to do so could result in 

personal injury due to discharge of high-pressure water.

Taking a break

If you are taking a break of five minutes or more between 

cleaning tasks:

1.  Engage the gun safety lock.
2.  Turn the switch to the OFF (0) position.
3.  Unplug the power cord from the outlet.

Storage

Hose reel

1.  Unlock the hose reel by pulling out on the handle out  

(Fig. 19).

2.  Turn the handle counterclockwise to wind the hose  

(Fig. 20).

3.  Wind the hose until you reach the hose's end.
4.  Push the handle in to lock the reel.

m

CAUTION! 

Always store your pressure washer in a 

location where the temperature will not fall below 32ºF (0ºC). 

The pump in this machine is susceptible to permanent damage 

if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE 

WARRANTY.

•  Store the pressure washer indoors in a dry, covered area 

where it is not subject to adverse weather conditions.

• 

It is important to store this product in a frost-free area.

• 

Always empty water from all hoses, the pump, and the 

detergent bottle before storing.

m

CAUTION! 

The use of a pump protector is 

recommended to prevent cold weather damage during storage 

over the winter months.

Winterizing and long-term storage

If you must store your pressure washer in a location where 

the temperature falls below 32ºF (0ºC), you can minimize the 

chance of damage to your machine by utilizing the following 

procedure:

• 

Disconnect all water connections.

• 

Turn on the machine for a few seconds until the remaining 

water in the pump exits. Turn off immediately.

• 

Do not allow the high-pressure hose to become kinked.

• 

Store the machine and accessories in a room that does 

not reach freezing temperatures.

• 

Do not store near a furnace or other sources of heat that 

may dry out the pump seals.

•  Operate the pressure washer with non-corrosive/non-toxic 

anti-freeze, a pump saver, or a pump protector before 

storing for the winter.

Fig. 19

Hose reel handle

Fig. 20

Hose reel handle

Summary of Contents for SPX3001





















Reviews: