background image

10

Troubleshooting

m

WARNING!

 Only perform the steps described within 

these instructions! 

All further inspection, maintenance and repair work must 
be performed by an authorized service center or a similarly 
qualified specialist if you cannot solve the problem yourself!

Suspected malfunctions, disturbances or damages are often 
due to causes that the user can fix themselves. Therefore 
check the product using this section. In most cases the 
problem can be solved quickly.

Service and Support

If your Electric Dethatcher requires service or maintenance, 
please call 1-866-766-9563 for assistance.

Model and Serial Numbers

When contacting the company or reordering parts, you will 
need to provide the model and serial numbers of your product. 
These are found on the decal affixed to the housing or guard of 
your Electric Dethatcher. Copy these numbers into the space 
provided below:

Record the following numbers from the housing or handle of your  
new product:

A   J    8    0   0   E

Model #:

Serial #:

Problem 

 

 

      Possible cause  

 

   Solution

1. 

Product does not start

2. 

Product does not reach full 
power

3. 

Unsatisfying result

1. 

Not connected to power supply

2. 

Power cord or plug is defect

3. 

Other electrical defect to the 
product

1. 

Extension cord not suitable for 
operation with this product

2. 

Power source (e.g. generator) has 
too low voltage

3. 

Air vents are blocked

1. 

Cutting device worn

1. 

Connect to power supply

2. 

Check by an electrician

3. 

Check by an electrician

1. 

Use a proper extension cord

2. 

Connect to another power source

3. 

Clean the air vents

1. 

Have a specialist to replace it

Summary of Contents for AJ800E













Reviews: