background image

11    Appendix 

 

User Manual 

 

46

 

 

 

11.2   

Abbreviation Explanation 

Abbreviation 

Explanation 

PCC 

Point of Common Coupling 

BMS   

Battery Management System 

CAN 

Control Area Network 

CC 

Constant Current 

CP 

Constant Power 

CV 

Constant Voltage 

DOD 

Depth of Discharge 

MCCV 

Maximum Charge Current 

MDCV 

Maximum Discharge Current 

RH 

Relative Humidity 

SOC 

State of Charge 

SOH 

State of Health 

NTP 

Network Time Protocol 

11.3    Quality Assurance

 

Evidence 

Within the warranty period, SungrowSamsung (Hefei) will require the customer 
to present the purchase invoice and date. The trademark on the product shall 
be clearly visible. Otherwise, SungrowSamsung shall hold no liability. 

Conditions 

If the product covered by  warranty becomes defective during warranty period, 
SungrowSamsung (Hefei) will provide a totally-free repair or exchange. 

 

The unqualified product that is replaced shall be returned to 

SungrowSamsung (Hefei).

 

 

Customers shall leave proper time for us to repair the failed device.

 

Damage and claims arising from the followings are not covered by the warranty 
of SungrowSamsung (Hefei): 

 

Transport damage 

Summary of Contents for EMS200






















































Reviews: