background image

Operation manual of solar water controller SR868C8/SR868C8Q 
 

--------------------------------------------------------------------------------------------------------------------------------------------------- 

- 21 - 

 
 
 

exceeds  switch-

on  temperature  difference,  solar  pump  doesn’t  work  yet.  When 

temperature  of  collector  is  3

o

C  higher  that  the  preset  CMN  temperature,  solar  circuit 

pump is restarted, controller exits this program. 

 

Setup steps

To  access  main  menu  TEMP,  then  select  submenu  CMN,  “CMN

  -  -  -

”  displays  on 

screen, default set is off. 
 
►Press “SET” button, default off signal “- - -” blinks on screen. 
►Repress “SET” button, to activate and deactivate this function   
►Press “+”“-” button, to adjust the low protection temperature of collector CMN, 

adjustable range (00

℃~

90

), after activate the function, factory set is 10

 

► Press “ESC” button to exit the menu or wait for 20 seconds to exit automatically, 
parameters are saved automatically. 
 
 
 
 
 
 

CMN signal displays on screen, it indicates that this function is in activated. 

 

 

4.5.4 CFR frost protection of collector

 

Description: 

In  winter  when  the  temperature  of  collector  is  below  the  preset  frost  protection 

temperature  (factory  set  is  4

o

C),  Solar  circuit  pump  is  triggered.  Besides  when  tank 

temperature  (T2)  drops  to  4

o

C,  electrical  heater  is  triggered  automatically  and  it  is  in 

operation until T2 is heated up to 20

 o

C or it is stopped when program of CFR is exited. 

When collector temperature rises up to 7

 o

C, solar circuit pump is ceased, program of 

CFR exits automatically.   

 

This  function  is  used  in  system,  which  use  water  as  heat  transfer  liquid,  to  avoid  the 

freezing of solar heat transfer fluid.   
 

Setup steps: 

To access main menu TEMP, then select submenu CFR, “CFR

 - - -

” displays on screen, 

default set is off. 
►Press “SET” button, default off “- - -” blinks. 
►Repress “SET” button, to activate or 
deactivate this function 

Summary of Contents for SR868C8













































Reviews: