Linking Procedure (continued)
Linking Procedure (continued)
6
Transmitter Connection
Connect to
Preamplifier
or Receiver’s
SUB/LFE
OUTPUT
SUB/LFE
INPUT
7. Once linking is successful, verify that
your audio components and subwoofer
are powered off and connect the RCA
audio cable on the transmitter to the
“SUBWOOFER” or “SUB/LFE” output
of your audio system.
6
Transmitter Connection
Connect to
Preamplifier
or Receiver’s
SUB/LFE
OUTPUT
SUB/LFE
INPUT
7. Once linking is successful, verify that
your audio components and subwoofer
are powered off and connect the RCA
audio cable on the transmitter to the
“SUBWOOFER” or “SUB/LFE” output
of your audio system.
5
Note: The linking procedure is done
before
connecting the wireless transmit-
ter and receiver to your equipment.
1. Be sure that the AC power and the
RCA audio cables on both the wireless
receiver and transmitter are unplugged.
2. Connect power to
just
the transmitter,
by plugging it into a live AC outlet.
3. Press and hold the LINK button on the
transmitter, until the green LED begins
to blink (approximately 3 seconds).
4. Connect power to the receiver(s) within
30 seconds of the completion of step 3.
5. The green LED on the receiver(s) will
begin to blink slowly until it “links” with
the transmitter.
6. Once the linking sequence is complete,
the green LEDs on both the transmit-
ter and the receiver(s) will become
solid green. If after approximately
60 seconds either the transmitter or
receiver(s) LED continues to blink,
please repeat the linking procedure
starting at step 1.
continued
Linking Procedure
5. Subwoofer LFE Input
This line-level RCA input is only on the
transmitter. It connects to the subwoofer/LFE
output of an audio system using the supplied
RCA cable.
6. Power Input
Connect to the DC output of the supplied
AC/DC adapter. The voltage input is + 5V DC
on the pin, at 0.5A.
7. Subwoofer LFE Output
This line-level RCA output is only on the
receiver. It connects to the subwoofer/LFE
input of a Sunfire SDS subwoofer or to any
powered subwoofer with an LFE input, using
the supplied RCA cable.
7
Receiver Connection
Linking Procedure (continued)
OUTPUT
INPUT
R
L/
LFE
R
L
ON
AC INPUT
100–120 VAC
50/60 Hz 2A
OFF
POWER
150 Hz
CROSSOVER
FREQUENCY
PHASE
VOLUME
BYPASS
50 Hz
100 Hz
NORMAL
0
˚
180
˚
90
˚
MAX
MIN
0 dB
SUB/LFE
OUTPUT
L/LFE
INPUT
8. Connect the RCA audio cable on the
wireless receiver to the LFE INPUT on
your subwoofer.
8
© 201
1 Sunfire, a division of
The AVC Group LLC.,
All rights reserved. Sunfire reserves the right to
improve its products at any time. Therefore, speci-
fications are subject to change without notice.
Quick Start Guide 913-165-00 Rev B
Linking Procedure
(continued)
9. Turn on all of your audio equipment,
including the subwoofer.
10. T
o confirm the subwoofer is operating,
temporarily adjust the controls on the
subwoofer to the following: (you will
adjust these settings again later to
properly and permanently blend with
your speakers).
a. Turn the output volume on your
subwoofer at least half way up
b. Set the subwoofer Crossover
adjustment to bypass (furthest
clockwise setting)
c.
Set Phase adjustment to “0”
11. Test your subwoofer by playing a CD or
DVD and listening to the subwoofer to
confirm audio output.
12.
Once confirmed, set-up your subwoofer
according to the manufacturer’s
instructions.
13. Set up your receiver or surround
processor using the manufacturer's
instructions.
14. Your system should now be fully
functional and set up for years of
enjoyment!
SDSWiTX:
FCC ID: YT2SDSWITX2010
IC:
2488A-SDSWITX2010
SDSWiRX:
FCC ID: YT2SDSWIRX2010
IC:
2488A-SDSWIRX2010
Troubleshooting
Subwoofer does not play
•
Verify the subwoofer is plugged into an
unswitched AC outlet and turned on.
•
Check that the transmitter and receiver
are plugged into an unswitched AC
outlet .
•
Check that the RCA connection cable
between the audio system and the
transmitter is secure and in good
condition.
•
Check that the RCA connection
cable between the receiver and the
subwoofer is secure and in good
condition.
•
Verify that both the transmitter and
receiver(s) have solid green LEDs,
indicating a complete link.
•
Repeat the linking procedure if re-
quired.
•
Check that the receiver is not further
than 40 feet (one receiver system) or
25 feet (two receiver system) away
from the transmitter.
