Sunfire Cinema Seven User Manual Download Page 18

User's Manual

18

APPENDIX

© 2003 Sun

Þ

 re Corporation. 

All rights reserved. Sun

Þ

 re Corpora-

tion re serves the right to improve 
its products at any time. Therefore, 
speci

Þ

 cations are subject to change 

without notice.               

Man u al part # : 913-048-00 Rev A

Signature Edition

Power output

400 watts con tin u ous, per chan-
 nel, into eight ohms, from            
20 Hz to 20 kHz with no more 
than 0.5% T.H.D.

Power at clipping, min

800 watts per chan nel into four 
ohms.
1600 watts per chan nel into two 
ohms (time limited basis).

Hum and Noise

-118 dB, A-Weighted

Maximum output current

120 amps peak to peak per ch.

Maximum output voltage

57 Vrms

Output impedance Front 
Left and Right channels

Voltage source: Approx. zero ohms
Current source: Approx. one ohm

RCA Input impedance:

24 k

Input sensitivity for rated 
output

Unbalanced:  1.9 Vrms         
Bal anced:      0.95 Vrms

XLR Input impedance:

24 k

, each leg balanced to 

ground    Female XLR                      

     Pin 1 is ground                          
     Pin 2 is positive (hot)                
     Pin 3 is negative (cold)

12 VDC Trigger Inputs

Input voltage range   5 -18 VDC
Impedance: approx 600 

             

                    (20 mA @ 12 V)

Power Consumption

45 W           At idle                            
580 W         Typical (1/8th power)    
1800 W       Ab so lute Max (Fuse      

                  Limit)

Dimensions and Weight

19.0 inches wide                             
6.5 inches high (including feet)       
16.7 inches deep (to tips of con-
nectors)                                           
Weight 44 lbs
Architect's Choice:                          
17.0 inches wide                             
5.9 inches high (including feet)       
16.7 inches deep (to tips of con-
nectors)                                           
Weight 40 lbs

Finish

Brushed aluminum with black 
anodize

Standard Edition

Power output

200 watts con tin u ous, per chan-
 nel, into eight ohms, from            
20 Hz to 20 kHz with no more 
than 0.5% T.H.D.

Power at clipping, min:

400 watts per chan nel into four 
ohms.
800 watts per chan nel into two 
ohms (time limited basis).

Hum and Noise

-115 dB, A-Weighted

Maximum output current

80 amperes peak to peak per         

     channel

Maximum output voltage

40 Vrms

Output impedance Front 
Left and Right channels

Voltage source: Approx. zero ohms
Current source: Approx. one ohm

RCA Input impedance

24 k

Input sensitivity for rated 
out put

Unbalanced:  1.34 Vrms                 
Bal anced:      0.67 Vrms

XLR Input impedance

24 k

, each leg balanced to 

ground    Female XLR

     Pin 1 is ground                          
     Pin 2 is positive (hot)                
     Pin 3 is negative (cold)

12 VDC Trigger Inputs

Input voltage range   5 -18 VDC
Impedance: approx 600 

             

                    (20 mA @ 12 V)

Power Consumption

45W            At idle                            
280W          Typical (1/8th power)    
1800W        Ab so lute Max (Fuse      

                  Limit)

Dimensions and Weight

19.0 inches wide                             
6.5 inches high (including feet)       
16.7 inches deep (to tips of con-
nectors)                                 
Weight 38 lbs
Architect's Choice:                          
17.0 inches wide                             
5.9 inches high (including feet)       
16.7 inches deep (to tips of con-
nectors)                                 
Weight 34 lbs

Finish

Brushed aluminum with black 
anodizing

Speci

Þ

 cations

Summary of Contents for Cinema Seven





















Reviews: