Sunfire cinema grand Series II User Manual Download Page 23

23

User's Manual

Sunfire Corporation is proud of its prod-

ucts which have been built with care using
advanced technology and premium compo-
nent parts. Your unit has been crafted to
perform properly for many years. Sunfire
Corporation offers the following warranty to
you, the owner of a new Sunfire product:

The Sunfire Corporation Warranty for the

Sunfire Amplifier is in effect for FIVE years
from the date of original retail purchase. The
Sunfire Corporation Warranty covers defects
in materials and workmanship. However, the
following are excluded: a) damage caused
during shipment, b) damage caused by
accident, misuse, abuse of operation contrary
to the instructions specified in the Sunfire
Corporation user’s manual, c) units where the
serial number has been defaced, modified or
removed, d) damage resulting from modifica-
tion or attempted repair by any person other
than authorized by Sunfire Corporation.

The Sunfire Corporation Warranty

extends to the original owner or subsequent
owner(s) during the five year warranty period
so long as the original dated purchase receipt
is presented whenever warranty service is
required.

All implied warranties, including warran-

ties or merchantability and fitness for particu-
lar purposes, are limited in duration to the five
year length of this warranty, unless otherwise
provided by state law.

Sunfire Corporation’s liability is limited to

the repair or replacement, at our option, of
any defective product and shall not in any
event include property or any other incidental
or consequential damages which may result
from the failure of this product.

Some states do not allow limitations on how

long an implied warranty lasts and/or do not
allow the exclusion or limitation of incidental or
consequential damages, so the above limita-
tions or exclusions may not apply to you.

This Warranty gives you specific legal

rights, and you may also have other rights
which vary from state to state. We suggest
that you attach your purchase receipt to this
Warranty and keep these in a safe place.
Thank you for your choice of a Sunfire
Corporation product.

Service Assistance

We suggest that you read the Limited

Warranty completely to fully understand your
Warranty/Service coverage.

If your Sunfire Corporation product ever

requires service, write or call to:

Sunfire Corporation
Technical Services Department
P.O.Box 1589,
Snohomish, WA 98291
Tel (425) 335-4748
Fax (425) 335-4746

You will be directed to an authorized

Sunfire Corporation Service Station or receive
instructions to ship the unit to the factory.
Please save the original shipping carton and
packing materials in case shipping is required.
Please do not ship Parcel Post.

NOTE:

 Before sending in your unit for repair,

you must call Sunfire for return authorization.

Include a complete description of the

problem, indicating how you have it con-
nected, the associated equipment in your
system and a copy of your purchase receipt.
Initial shipping costs are not paid by Sunfire
Corporation; return ground shipping costs will
be prepaid if repairs were covered by the
scope of this warranty.

Limited Warranty

Limited Warranty

Summary of Contents for cinema grand Series II

























Reviews: