background image

1

Rev. 04/10/03

90025

1.7mm

Gravity Feed

HVLP Spray

Gun & Cup

w/ Regulator

Operating Instructions • Warning Information • Parts Breakdown

SPECIFICATIONS

Fluid Orifice .......................................................... 1.7mm

Air Inlet:  ..................................................................1/4 NPT

Rec. Max. Inlet Pressure:  ..............................................43 PSI

CFM:  ................................................................ 13 at 43 PSI

Nozzle Pressure  .......................................................... 10 PSI

Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement 

and other masonry products, and

• arsenic and chromium from 

chemically-treated lumber.

Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.

ALWAYS READ 
INSTRUCTIONS
BEFORE USING
POWER TOOLS

ALWAYS WEAR 
SAFETY GOGGLES

WEAR HEARING 
PROTECTION

AVOID 
PROLONGED 
EXPOSURE TO 
VIBRATION

90025_OpMan  4/18/03  1:57 PM  Page 1

Summary of Contents for 90025









Reviews: