background image

     M A T E R I A L   S A F E T Y   D A T A   S H E E T           PAGE: 5

        Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED

         Product Code: 04632

         Effective Date: 08/03/04     Date Printed: 08/04/04     MSD: 002239

     ------------------------------------------------------------------------

           CHEMICAL STABILITY:  Thermally stable at typical use temperatures.

           CONDITIONS TO AVOID:  Avoid use temperatures above 450F, 232C.

             Product can degrade at elevated temperatures.  Generation of gas

             during decomposition can cause pressure in closed systems.

           INCOMPATIBILITY WITH OTHER MATERIALS:  Avoid contact with

             oxidizing materials.  Avoid contact with strong acids.

           HAZARDOUS DECOMPOSITION PRODUCTS:  Hazardous decomposition

             products depend upon temperature, air supply and the presence

             of other materials.

           HAZARDOUS POLYMERIZATION:  Will not occur.

     11. TOXICOLOGICAL INFORMATION (See Section 3 for Potential Health

           Effects. For detailed toxicological data, write or call the

           address or non-emergency number shown in Section 1)

           SKIN:  The LD50 for skin absorption in rabbits is >10,000 mg/kg.

           INGESTION:  The oral LD50 for rats is 20,000 - 34,000 mg/kg.

           MUTAGENICITY:  In vitro mutagenicity studies were negative.

             Animal mutagenicity studies were negative.

     12. ECOLOGICAL INFORMATION (For detailed Ecological data, write or call

           the address or non-emergency number shown in Section 1)

           ENVIRONMENTAL FATE

             MOVEMENT & PARTITIONING:  Based largely or completely on data

               for major component(s).  Bioconcentration potential is low

               (BCF less than 100 or Log Pow less than 3).  Potential for

               mobility in soil is very high (Koc between 0 and 50).

             DEGRADATION & PERSISTENCE:  Based largely or completely on data

               for major component(s).  Material is readily biodegradable.

               Passes OECD test(s) for ready biodegradability.  Degradation

               is expected in the atmospheric environment within minutes to

               hours.

           ECOTOXICITY:  Based largely or completely on data for major

             component(s).  Material is practically non-toxic to aquatic

             organisms on an acute basis (LC50/EC50 >100 mg/L in most

     (Continued on page 6 , over)

     * OR (R) INDICATES A TRADEMARK OF THE DOW CHEMICAL COMPANY

     M A T E R I A L   S A F E T Y   D A T A   S H E E T           PAGE: 6

        Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED

         Product Code: 04632

         Effective Date: 08/03/04     Date Printed: 08/04/04     MSD: 002239

     ------------------------------------------------------------------------

             sensitive species).

     13. DISPOSAL CONSIDERATIONS (See Section 15 for Regulatory Information)

           DISPOSAL:  DO NOT DUMP INTO ANY SEWERS, ON THE GROUND OR INTO ANY

             BODY OF WATER. All disposal methods must be in compliance with

             all Federal, State/Provincial and local laws and regulations.

             Regulations may vary in different locations.  Waste character-

             izations and compliance with applicable laws are the responsi-

             bility solely of the waste generator.  THE DOW CHEMICAL COMPANY

             HAS NO CONTROL OVER THE MANAGEMENT PRACTICES OR MANUFACTURING

             PROCESSES OF PARTIES HANDLING OR USING THIS MATERIAL.  THE

             INFORMATION PRESENTED HERE PERTAINS ONLY TO THE PRODUCT AS

             SHIPPED IN ITS INTENDED CONDITION AS DESCRIBED IN MSDS SECTION 2

             (Composition/Information On Ingredients).

             FOR UNUSED & UNCONTAMINATED PRODUCT, the preferred options in-

             clude sending to a licensed, permitted:  recycler, reclaimer,

             incinerator or other thermal destruction device.

             As a service to its customers, Dow can provide names of

             information resources to help identify waste management

             companies and other facilities which recycle, reprocess or

             manage chemicals or plastics, and that manage used drums.

             Telephone Dow's Customer Information Center at

             800-258-2436 or 989-832-1556 for further details.

     14. TRANSPORT INFORMATION

           DEPARTMENT OF TRANSPORTATION (D.O.T.):  For D.O.T. regulatory

           information, if required, consult transportation regulations,

           product shipping papers, or contact your Dow representative.

           CANADIAN TDG INFORMATION:  For TDG regulatory information, if

           required, consult transportation regulations, product shipping

           papers, or your Dow representative.

     15. REGULATORY INFORMATION (Not meant to be all-inclusive--selected

           regulations represented)

     NOTICE: The information herein is presented in good faith and

     believed to be accurate as of the effective date shown above. However,

     no warranty, express or implied is given. Regulatory requirements

     are subject to change and may differ from one location to another;

     it is the buyer's responsibility to ensure that its activities comply

     with federal, state or provincial, and local laws. The following

     (Continued on page 7)

     * OR (R) INDICATES A TRADEMARK OF THE DOW CHEMICAL COMPANY

     M A T E R I A L   S A F E T Y   D A T A   S H E E T           PAGE: 7

        Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED

         Product Code: 04632

         Effective Date: 08/03/04     Date Printed: 08/04/04     MSD: 002239

     ------------------------------------------------------------------------

     specific information is made for the purpose of complying with

     numerous federal, state or provincial, and local laws and regulations.

     See other sections for health and safety information.

     U.S. REGULATIONS

     ====================

     SARA 313 INFORMATION:  To the best of our knowledge, this product

     contains no chemical subject to SARA Title III Section 313 supplier

     notification requirements.

                   ---------------------

     SARA HAZARD CATEGORY:  This product has been reviewed according to the

     EPA "Hazard Categories" promulgated under Sections 311 and 312 of the

     Superfund Amendment and Reauthorization Act of 1986 (SARA Title III) and

     is considered, under applicable definitions, to meet the following

     categories:

     Not to have met any hazard category

                   ---------------------

     TOXIC SUBSTANCES CONTROL ACT (TSCA):

     All ingredients are on the TSCA inventory or are not required to be

     listed on the TSCA inventory.

     -----

                   ---------------------

     STATE RIGHT-TO-KNOW:  The following product components are cited on

     certain state lists as mentioned.  Non-listed components may be shown

     in the composition section of the MSDS.

     CHEMICAL NAME                                 CAS NUMBER   LIST

     --------------------------------------------  -----------  ------------

     1,2-PROPANEDIOL                               000057-55-6  PA1

     PA1=Pennsylvania Hazardous Substance (present at greater than or equal

         to 1.0%).

                   ---------------------

     OSHA HAZARD COMMUNICATION STANDARD:

     (Continued on page 8 , over)

     * OR (R) INDICATES A TRADEMARK OF THE DOW CHEMICAL COMPANY

     M A T E R I A L   S A F E T Y   D A T A   S H E E T           PAGE: 8

        Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED

         Product Code: 04632

         Effective Date: 08/03/04     Date Printed: 08/04/04     MSD: 002239

     ------------------------------------------------------------------------

     REGULATORY INFORMATION (CONTINUED)

     This product is not a "Hazardous Chemical" as defined by the OSHA

     Hazard Communication Standard, 29 CFR 1910.1200.

     CANADIAN REGULATIONS

     ====================

     WHMIS INFORMATION: The Canadian Workplace Hazardous Materials

     Information System (WHMIS) Classification for this product is:

     This product is not a "Controlled Product" under WHMIS.

                   ---------------------

     CANADIAN ENVIRONMENTAL PROTECTION ACT (CEPA):

     This product contains one or more substances which are not listed on

     the Canadian Domestic Substances List (DSL).  Contact your Dow

     representative for more information.

     16. OTHER INFORMATION

           MSDS STATUS:  Revised Section 8 (Exposure Guidelines).

     * OR (R) INDICATES A TRADEMARK OF THE DOW CHEMICAL COMPANY

     The Information Herein Is Given In Good Faith, But No Warranty,

     Express Or Implied, Is Made.  Consult The Dow Chemical Company

     For Further Information.

Appendix E

Summary of Contents for SolaRay AC





















































Reviews: