Sundstrom SR 530 Operating Instruction Download Page 7 | Manualshive

Page: 7 / 15

background image

Drawn up by:

2012-04-11 /RK

HI-SR 530 USA

Revision:

01

Reviewed:

Page:

7 of 15

Make sure that the breathing hose runs
along your back and is not twisted.

4.4 Doffing the hood

Leave the polluted area before
removing the respiratory protection inlet
covering and SR 500 PAPR fan unit.

Take off the respiratory inlet covering.

Switch off the fan.

Release the belt and remove the fan
unit.

After use, the SR 500 components must
be cleaned, inspected and prepared for
reuse (e.g. charge the batteries).

«
...
5
6
7
8
9
...
»

Summary of Contents for SR 530
















Reviews:

No comments

Related manuals for SR 530

Brand: e-breathe Pages: 47

DeVilbiss ProViSOR PROV-650 Series

Brand: Carlisle Pages: 12

Brand: Sleepnet Pages: 2

Brand: Sleepnet Pages: 12

Brand: 3M Pages: 2

Ultralite 2 BIBS

Brand: JFD Pages: 60

YPHD YD-003 FFP3 NR

Brand: IRUDEK Pages: 2

Brand: AWR Pages: 32

Brand: Kerbl Pages: 2

Brand: Clemco Pages: 7

Brand: Clemco Pages: 14

Brand: Clemco Pages: 14

Brand: Clemco Pages: 18

BLAST HELMET APOLLO 600 CE

Brand: Clemco Pages: 19

cleanSy Pearl WT-3WF1

Brand: Zepter Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands