background image

Head Office  

Factory

Tel: +46-(0)8-562 370 00  

Tel: +46-(0)8-562 370 00

Fax: +46-(0)8-562 370 20  

Fax: +46-(0)8-562 370 60

Visiting address:  

Visiting address:

Stockholmsvägen 33  

Västergatan 4

SE-181 33 Lidingö 

SE-341 50 Lagan

www.srsafety.com

Product leaflet

The SR 100 half mask is made of silicone in three sizes, i.e. S/M, M/L and L/XL. The mask is equipped with 
two exhalation valves, which ensures very low exhalation resistance. The valve covers with partitions effectively 
protect the exhalation membrane against dust and paint mist. The material and pigment of the mask body are 
approved by FDA and BGA for foods, which minimizes the risk of contact allergies. The easily adjustable elastic 
head harness straps of the mask are designed as a V-shaped loop and have a large dished crown plate, which 
contributes towards a comfortable and safe fit. The mask is used either as a filtering device in combination with 
filters from the Sundström range, or in combination with the SR 307 compressed air attachment which then 
serves as a breathing apparatus with continuous flow for connection to a compressed air supply.
A pre-filter holder is supplied. Best stored in box SR 230 or storage case SR 339.

P01H-2018 Rev 09 20160816

Product  

Model No.  

Ordering No.

Half mask 

SR 100 S/M 

H01-2112 

 

SR 100 M/L 

H01-2012 

 

SR 100 L/XL 

H01-2812

Product Description

Technical specification

A.   Mask body
B.   Filter attachment
C.   Head harness straps
D.   Exhalation valve seat
E.   Exhalation membrane
F.   Inhalation valve seat
G.   Inhalation membrane
H.   Protective cap
I.   Filters (not included)
J.   Pre-filter
K.   Pre-filter holder

 

SR 100 

EN 140:1998

Inhalation resistance at 30 l/min 

 

≈ 3 Pa  

≤ 50 Pa

Exhalation resistance at 160 l/min 

 

≈ 70 Pa  

≤ 300 Pa

Service temperature

 

-10 – +55 °C, < 90 % RH 

-

Storage temperature

 

-20 – +40 °C, < 90 % RH 

-

Weight 

 

≈ 179 g  

-

Assigned Protection Factor¹ 

 

20 (P3) 

 

10 (GasX) 

 

10 (GasX P3) 

-

Nominal Protection Factor

2

 

48 (P3)  

 

50 (GasX) 

 

48 (GasX P3) 

-

Approval  

 

EN 140:1998

1) Specified in BS 4275, and applies generally to all half masks with particle filters P3, regardless of the test results. 
2) According to EN 529:2005.

G

A

B

F

J

K

H

E

D

C

I

Tel.: +49 (0)40 - 88 90 100

www.toplicht.de

Schiffsausrüster

Summary of Contents for H01-2012







Reviews: