background image

Installation Instructions

SB-CM46A12

7

Attaching Faceplate to Pipe

CAUTION:

Watch for pinch points. Do not place fingers

between movable parts.

1.

Thread the faceplate (G) onto pipe (A) until tight. (See
Figure 7)

2.

Install and tighten the 5/16-18 x 1/4” set screw (H) using the
5/32” hex key (E). (See Figure 7)

Figure 7

Interface Bracket Assembly

1.

Use four #10-24 x 1/2” button head cap screws (L) and 1/8”
hex key (N) to attach four mounting buttons (M) to two
center brackets (K). (See Figure 8)

2.

Use four #10-24 x 1/2” button head cap screws (L) and 1/8”
hex key (N) to attach side brackets (J) to center brackets
(K). (See Figure 8)

Figure 8

Display Installation

WARNING:

IMPROPER INSTALLATION CAN LEAD TO

EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT
substitute hardware. Use only hardware supplied by
manufacturer!

WARNING:

IMPROPER INSTALLATION CAN LEAD TO

ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT! Screw
length must not exceed the depth of threaded mounting insert
in display.

WARNING:

OVERTIGHTENING OF SCREWS CAN

DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT over
tighten screws when installing interface bracket.

WARNING:

IMPROPER INSTALLATION CAN LEAD TO

DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
Ensure that screws are not too long.

WARNING:

IMPROPER INSTALLATION CAN LEAD TO

DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread
engagement in display may cause display to fall! Back out
screws ONLY as necessary to allow installation of Centris
cup!

1.

Remove the four mounting screws and washers that came
installed on the back of the display. (See Figure 9)

2.

Use four removed screws and washers to attach side
brackets (N) to display. (See Figure 9)

Figure 9

(G)

(A)

2

1

(H) x 1

(L) x 4

2

(J) x 2

(K) x 2

(L) x 4

1

(M) x 4

2

x 4

1

removed screws x 4

(J) x 2

Summary of Contents for SunBriteTV SB-CM46A12













Reviews: