4
Always disconnect the kettle from the power
outlet before cleaning.
Never immerse the kettle switch area, cord or
power base in water, or allow moisture to
come into contact with these parts.
Descale Your Kettle Regularly.
Mineral deposits in tap water solidify when
the water is heated; lime scale may be white,
coloured, even rusty-looking and is normally
visible. Phosphate scale isn't generally visible
however it may cause the water to appear
cloudy when heated. This may cause the
interior of the water gauge to discolour, cause
overheating, trigger the boil-dry cut-out
mechanism or even reduce the kettle’s life.
Even in soft water areas it is important to
descale your kettle regularly to help maintain
its lifecycle.
NOTE: Failure to descale products regularly
can be deemed as negligent handling and
any faults caused by mineral build up will
not be covered by the Sunbeam 12 Month
Guarantee.
To remove this build-up, use Sunbeam Liquid
Descaler, a simple to use, non-toxic cleaner
available from Sunbeam Appointed Service
Agents.
Alternatively:
1. Fill the kettle with 1 cup of white vinegar
and the remainder with water and allow to
stand overnight. DO NOT BOIL.
2. Empty the solution from the kettle. Any
stains remaining inside the spout can be
removed by rubbing with a damp cloth. Fill
the kettle with clean water, bring to boil
and then discard the water. Repeat and the
kettle will then be ready to use.
Cleaning the concealed heating element
This kettle features a non-corrosive stainless
steel heating element. Over time, scale may
build up on the concealed element inside the
kettle, causing discolouration that may have
the appearance of rust. Be assured this is not
rust. If this occurs clean with a Scotchbrite
®
scourer or similar and a suitable abrasive
cleaning cream. Rinse and clean thoroughly
with tap water before using your kettle again.
To clean the exterior
The surface of the kettle may be wiped over
with a damp cloth and polished with a soft
dry cloth.
Take care not to knock or damage the
paintwork, as this may result in areas where
the finish does not retain its original
character. Clean the exterior of the product
by wiping with a soft, lint-free damp cloth.
CAUTION: Do not use any polishing agents,
chemicals, steelwool or abrasive cleaning
products to clean the outside of the kettle as
these can damage the appearance.
To clean the mesh filter
CAUTION: Before removing or refitting the
filter, switch off the kettle and empty it.
Allow it to cool completely, then unplug the
power base from the main supplied socket.
Never operate the kettle without the filter
fitted.
Open the Lid. Grasp the top of the mesh
filter and pull upwards to remove. Wash in
warm soapy water and dry thoroughly before
replacing in the kettle.
CAUTION: To prevent damage to the appliance
do not use alkaline cleaning agents when
cleaning, use a soft cloth and mild detergent.
Care and Cleaning
THE NEW YORK COLLECTION
KETTLE
User Guide
Need help with your appliance?
Contact our customer service team
or visit our website for information
and tips on getting the most from
your appliance.
Australia
|
visit
www.sunbeam.com.au
phone
1300 881 861
Units 5 & 6, 13 Lord Street,
Botany NSW 2019 Australia.
New Zealand
|
visit
www.sunbeam.co.nz
phone
0800 786 232
Level 6, Building 5,
Central Park,
660–670 Great South Road,
Greenlane, Auckland.
Sunbeam Corporation Limited | ABN 45 000 006 771
Sunbeam Corporation is a division of Newell Brands.
Sunbeam is a registered trade mark.
Made in China to Sunbeam’s specification.
Due to minor changes in design or otherwise,
the product you buy may differ slightly from the one shown here.
Approved by the appropriate electrical regulatory authorities.
©Copyright Sunbeam 2019.
02/2019
GCDS-SUN375525-SL
Australia
www.sunbeam.com.au
1300 881 861
Units 5 & 6,
13 Lord Street,
Botany NSW 2019
Australia
New Zealand
www.sunbeam.co.nz
0800 786 232
Level 6, Building 5,
Central Park,
660-670 Great South Road,
Greenlane, Auckland
New Zealand
KE4410
KE4430
