manualshive.com logo in svg

Sun Nuclear Radon 1028, User Manual

Share
Download
Sun Nuclear Radon 1028 User Manual Download Page 33

27

Connecting to Computer

The radon monitor can be connected to a computer using the USB cable provided 
with the radon monitor. 
If the computer does not have a USB port, a serial cable can be used to connect 
the radon monitor to the computer. See 

Optional Serial Connection

 on page 50.

1 

Ensure that the radon monitor software has been installed on the computer. 

2 

Connect the USB cable to the computer and the radon monitor (Figure 15). 

Figure 15. USB Connection to a Computer

3 

If desired, plug the power supply cord into a 100 to 240 VAC, 1-phase, 50-60 
Hz mains power source. 

Launch Software

1 

Ensure that the radon monitor is connected to the computer via a USB or 
serial cable.

2 

Launch the software application by double-clicking the 

Radon Monitor

 

desktop shortcut 

 or by selecting 

Start > Programs > SNC Group > 

Radon Monitor

.

3 

If the ‘Select Port’ window is displayed, select the port and then save it. See 

Port Selection

 on page 51.

Note: 

If the software does not detect the port, select it manually by 

selecting 

Setup > Select Serial Port

 from the on-screen menu. See 

Serial Port Setup on page 50.

Summary of Contents for Radon 1028





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands