manualshive.com logo in svg

Sun Fire X4600, Installation Manual

Share
Download
Sun Fire X4600 Installation Manual Download Page 25

■

CMA extension

Caution –

You can damage the I/O and power cables if you slide the system from the rack

without first running all cables at the rear through the CMA.

This section has the following procedures.

■

“How to Attach the Cable Management Arm (CMA)” on page 25

■

“How to Verify Cable Management Arm (CMA) Operation” on page 28

■

“How to Remove the Cable Management Arm (CMA)” on page 28

▼

How to Attach the Cable Management Arm (CMA)

Note –

Do not run cables from another server through the CMA. Use one CMA per server.

The CMA comes with the

4U Express Rail Rackmounting Kit

card that contains illustrations

that you should refer to during this procedure.

This procedure assumes that you have installed the server into the rack. See

“How to Insert the

Server Into the Rack” on page 21

.

If necessary, slide the server back until it is fully inside the rack.

Unpack the CMA parts and take them to the rear of the equipment rack.

Note –

References to “left” or “right” in this procedure assume that you are facing the rear of the

equipment rack.

Before You Begin

1

2

Installing the Cable Management Arm (CMA)

25

Summary of Contents for X4600



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands