Mechanical Inspection
Inspect the unit’s mechanical integrity every 400-500 hours of use.
• Inspect the unit’s fasteners verifying that all are firmly in place.
Pay particular attention to the hinge bolts.
• Inspect gas springs for signs of wear. Replace gas springs that will
not hold the canopy in the full open position when raised.
• Inspect the AC power cord and its connections.
• Inspect the acrylic. Replace if broken, cracked or badly scratched.
Removing/Replacing Acrylic Shield (bench)
The acrylic shield in the bench and metal grill in the canopy are
secured in place by hinged profiles which run the length of the bed,
both front and back. Simply pry up on the inside edge of the profile
until it releases its latching action (see figure below). Continue to pry
up the profile across its entire length until it swings back freely. Repeat
for the other profile. The long edges of the acrylic shield are now
exposed. Standing in front of the sunbed, grasp the long exposed edge
of the acrylic and carefully slide it toward you until it is removed.
Removing/Replacing Canopy Grill
Follow the above directions for opening the hinged profiles. As you
pry the hinged profile open the canopy grill should start to drop out
on its own. If you need to, slide the grill toward the head or foot end
of the sunbed and it will drop out easily.
After changing the lamps, replace
the bench acrylic shield and
canopy grill by reversing the
above directions. Close the
hinged profile by pushing it
back into place until it
snaps tight.
PROFILE
CAUTION
Be careful. The edges of the
acrylic shield may be sharp.
Start pulling from the
middle of the profile!
Operation
1
Set the timer to the desired number of minutes
(after first determining the proper time period
from the table above). The lamps will turn
on as soon as you turn the dial from the “0”
position.
2
Lift the canopy, lie down on the bench
(face up), and lower the canopy toward your
body. For best results, position the canopy as
close as possible to your body.
3
When the timer reaches 0, the lamps automatically turn off.
Using Your Sunbed
Before using your sunbed, please note the following:
• Your skin should be free of cosmetics, tanning oils, or other body
lotions prior to tanning except for those specifically made for use
with tanning devices. However, do not remove natural body oils by
bathing or showering immediately before tanning.
• Keep treated hair from contacting sunbed surfaces. Many hair prod-
ucts can damage the sunbed acrylic. Wear a shower cap or towel if
you use gels, mousses, sprays, or other hair products.
• Your sunbed is designed for individual use. Always wear the safety
goggles supplied with your sunbed or another approved pair of gog-
gles, as defined under 21 CFR 1040.20. Regular sunglasses do not
provide adequate protection from ultraviolet light.
• Follow the exposure guidelines and usage frequency outlined in the
Safety Information on the front.
Replacing Lamps
To be assured of maximum tanning effectiveness, change lamps after
approximately 800-1000 hours of use. Tanning will continue after this
time but at a slower rate. To ensure trouble-free operation of your
sunbed, replace the lamp starters whenever the lamps are replaced.
Use of uncertified lamps is a violation of Federal regulations and may
void your warranty (see certified lamps on first page).
1.
Grasp a lamp at one end and at the middle, then turn the lamp a
quarter turn. The lamp may then be gently removed from its holder.
2.
To reinstall lamp, insert pins on the ends of the lamp into the slots
on top of the lamp holder and turn the lamp a quarter turn.
Care and Maintenance
Cleaning After Use
Clean and disinfect your tanning bed’s bench and canopy after each
use. Use a non-abrasive disinfectant cleaner that
does not contain
ammonia or ammonia derivatives
. Ammonia may damage the acrylic
shield. Spray the acrylic lightly with disinfectant and wipe dry with a
clean soft cloth. Wipe the canopy grill with a soft cloth slightly damp-
ened with disinfectant, then wipe dry.
Thorough Periodic Cleaning
The cooling fans draw air through the bed and will cause a dust
buildup on the lamps and reflectors. When a dust buildup is observed,
it is necessary to thoroughly clean the inside of the bench and canopy.
1
Remove the acrylic shield, metal grill and lamps.
2
With a soft cloth, wipe the entire length of each lamp.
3
Clean both sides of the acrylic shield and grill with a non-ammo-
nia disinfectant cleaner.
4
Wipe the reflectors with a clean damp cloth.
5
Re-install the lamps, acrylic shield and grill.
On the front of each leg are two holes
for skirt mounting brackets. Locate
the two brackets and attach them as
shown with two #10-32 x 1/2” screws
and two #10-32 locking nuts each.
12
Attach the sirt as shown by inserting the tabs
along the top of the skirt into the slots in the
bottom of the bench cover and tucking the
bottom edge under the skirt mounting
brackets. Adjust the skirt mounting brackets
to secure the skirt.
13
