background image

 

INSTALLING THE STAINLESS STEEL HANDLE 

This beverage merchandiser includes a stainless steel handle that is not required to operate the unit. To 
install the handle, follow the instructions below: 

1.  Remove the door gasket on the side you wish to install the 

handle - you can see two designated holes for handle 
installation. The gasket is easily displaced by hand, no tools 
are necessary. 

2.  Install the handle tightly as shown with two screws, lock 

washers and flat washers provided. (DO NOT over tighten as 
this will cause damage to the handle and stainless steel door 
frame). 

3.  Replace the door gasket to its original position. 
 
 

 
 

OPERATING YOUR APPLIANCE

 

 

It is recommended you install the appliance in a place where the ambient temperature is between 60 and 
90°F (16 – 32°C), although optimum performance occurs when the temperature range is 72 and 78ºF (23 
– 26ºC).  If the ambient temperature is above or below the recommended temperatures, the performance 
of the unit may be affected.  For example, placing your unit in extremely cold or hot conditions may cause 
interior temperatures to fluctuate.  The range of 34º – 43ºF (1º – 6ºC) may not be reached. 
 
 

CONTROL PANEL 
 

TEMP

 

 

     LIGHT 

 

          Press to turn the inner light on or off. 

 

     UP 

 

 

         Used to raise (warm) the set temperature by 1°F/°C. 
 

     DOWN  

 

         Used to lower (cool) the set temperature by 1°F/°C.  

 

     ºF/ºC

 

Selector 

 

         Choose to display temperature setting in Fahrenheit or Celsius. To change the temperature from   
         Fahrenheit to Celsius or from Celsius to Fahrenheit, press the 

  button for at least 5 seconds. 

 

Setting the Temperature Control 

  You can set the temperature by pressing the

 UP 

and

 DOWN 

buttons. When you press the two 

buttons for the first time, the LED readout will show the original temperature set previously. (The 
temperature preset at the factory is 38°F or 3°C.) 

Handle

Door Frame

Gasket

Screw

Lock Washer

Flat Washer

 

Summary of Contents for SCR215L













Reviews: