background image

 

 

Electrical Connection 

 

 
 
 
 
 

This  unit  should  be  properly  grounded  for  your  safety.    The  power  cord  of  this  unit  is  equipped  with  a 
three-prong  plug  which  mates  with  standard  three-prong  wall  outlets  to  minimize  the  possibility  of 
electrical shock. 
 
Do not under any circumstances cut or remove the third ground prong from the power cord supplied. For 
personal safety, this appliance must be properly grounded.  
 
This unit requires a standard 115/120 Volt AC ~/60Hz electrical outlet with three-prong ground. Have the 
wall  outlet  and  circuit  checked  by  a  qualified  electrician  to  make  sure  the  outlet  is  properly  grounded. 
When  a  standard  2-prong  wall  outlet  is  encountered,  it  is  your  responsibility  and  obligation  to  have  it 
replaced with a properly grounded 3-prong wall outlet.  
 
The cord should be secured behind the unit and not left exposed or dangling to prevent accidental injury. 

 

The unit should always be plugged into its own individual electrical outlet which has a voltage rating that 
matches  the  rating  label  on  the  appliance.  This  provides  the  best  performance  and  also  prevents 
overloading house wiring circuits that could cause a fire hazard from overheating. Never unplug the unit 
by pulling the power cord.  Always grip the plug firmly and pull straight out from the receptacle. Repair or 
replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord 
that shows cracks or abrasion damage along its length or at either end. When moving the unit, be careful 
not to damage the power cord. 
 
 

 

Extension Cord 

Because of potential safety hazards under certain conditions, it is strongly recommended that you do not 
use an extension cord with this unit. However, if you must use an extension cord, it is absolutely 
necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord having a grounding 
type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes. 

 
 

 

Reversing the Door Swing of Your Appliance 

This appliance has the capability of the door opening from either the left or right side. The unit is delivered 
to you with the door opening from the left side. Should you desire to reverse the opening direction, please 
call service for reversal instructions. 
 
 

Warning

 

Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is 
damaged, have it replaced by an authorized Products service center. 

 

 

Summary of Contents for SBC582B

























Reviews: