Summit BROTHER HL-630 OPC User Manual Download | Manualshive

Page: 2 / 46

background image

2

Brother HL-1040 OPC

Brother Cartridge

Part #DR-300

OEM Stated Yield: 20,000

New drum cartridges come with a clear “Starter
Sheet” installed inside the cartridge. When the
cartridge is installed and the cover closed, the printer
will eject the sheet and at the same time, reset the
drum counter. This sheet is also present in the DR-
200 cartridges. Replacement sheets are now
available.

Brother HL-1240 OPC

Brother Cartridge

Part #DR-400 (DR-6000)

OEM Stated Yield: 20,000

Fax Machines (DCP Machines also)

After replacing the drum unit, keep the front cover
open and press “Clear”. The display will show
“Replace Drum? 1.Yes 2.No” Press “1” the display
will show “Accepted”, close the front cover. The
counter is reset!

MFC9700 Only:

After replacing the drum unit,

keep the front cover open and press “Right Arrow”
key. The display will show “Replace Drum? 1.Yes
2.No” Press “1”. Close the front cover. The counter
is reset!

Laser Printers

Open the front cover. Locate the black button under
the LED lights on the left side. Press and hold in the
button until all the lights are lit. Release the button.
The counter is reset!

Brother HL-1650 OPC

Brother Cartridge

Part #DR-500 (DR-7000)

OEM Stated Yield: 20,000

After replacing the drum unit, keep the front cover
open (make sure the power is on). Press and hold the
"GO" button for four seconds, the display will then
show "DRUM CLEAR". Close the front cover. The
counter is reset!

Brother HL-2040 OPC

Brother Cartridge

Part #DR-350 (DR-3000)

OEM Stated Yield: 12,000

Laser Printers:

make sure the machine is turned on

and the Drum LED is blinking. Press and hold the
GO button for 4 seconds until all the LEDs light up.
Once all the LEDs are lit, release the GO button.
The counter is Reset!

Fax machines:

After replacing the drum unit, keep

the front cover open (make sure the power is on).
Press OPTIONS on the display panel. When
REPLACE DRUM? Appears on the display, press
“1”, when ACCEPTED appears, close the front
cover. The counter is reset!

«
1
2
3
4
...
»

Summary of Contents for BROTHER HL-630 OPC















































Reviews:

No comments

Related manuals for BROTHER HL-630 OPC

Brand: Oki Pages: 2

Brand: Oki Pages: 52

Brand: Oki Pages: 117

Brand: Oki Pages: 45

Brand: Oki Pages: 112

Brand: Oki Pages: 115

Brand: Oki Pages: 2

Brand: Veris Industries Pages: 2

Brand: Kargo Master Pages: 13

Brand: Kargo Master Pages: 21

Brand: Kargo Master Pages: 4

Brand: Karel Pages: 56

Brand: Raven Pages: 70

Brand: Öhlins Pages: 10

Brand: +GF+ Pages: 36

Brand: Calix Pages: 5

Brand: Ricoh Pages: 2

Brand: pleasant hearth Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands