background image

2

OPERATING INSTRUCTIONS

CAUTION:

 NEVER BURN GARBAGE, REFUSE OR PAPER IN THE HEATING UNIT.

NEVER LEAVE COMBUSTIBLE OR OTHER MATERIALS AROUND OR NEAR THE FURNACE.

NOTE: AN OPTIONAL VESTIBULE IS AVAILABLE FOR THE SMO112 FURNACE

             THE VESTIBULE COMPLETELY ENCLOSES THE OIL BURNER

IDENTIFY THE LOCATION OF YOUR BURNER / FURNACE POWER SWITCH

OIL BURNER OPERATING INSTRUCTIONS

•  Use No 2 furnace oil 

ONLY

•  Do not use gasoline, crankcase oil, or any oil containing gasoline.

•  Do not attempt to start the burner if excess oil has accumulated, when the furnace is full of vapor, 

or if the combustion chamber is hot.

•  Press the burner relay reset button ONLY ONCE; if the burner fails to start, call an 

Oil Burner Technician.

•  If the oil burner is to be shut off for any period of time, shut the oil valve OFF at the oil tank.

•  Do not adjust or tamper with the furnace or any of the controls

•  Do not burn garbage or paper in this unit.

•  Never leave paper, rags, or other combustibles around the furnace.

•  Only qualified, or where required by law, a licensed technician shall set – up this unit and 

adjust controls.

•  DO NOT START THE OIL BURNER UNLESS THE BLOWER DOOR IS SECURED IN PLACE.

TO TURN THE BURNER OFF 

•  Turn the main oil burner switch to “ OFF “ 

•  Set the thermostat as far below room temperature as possible.

IF BURNER IS TO BE SHUT OFF FOR AN EXTENDED PERIOD.

•  Turn main oil burner switch to “OFF”.

•  Close all oil supply valves.

•  The heating system should be checked and cleaned if necessary.

BURNER FAILS TO OPERATE

Always call a qualified technician

The trouble may be :

•  Raise your  thermostat to 5º C ( 10º F ) above present room temperature

•  Make sure your “ Oil Burner “ power switch is in the “ON” position

•  If you hear a hum from the oil burner, and the motor has not started, press the reset button 

on the burner motor once only.

•  Blown fuse  / “tripped” breaker in electrical panel 

•  Thermostat may be set below room temperature.

•  Burner relay ( combustion control ) may have to  be  “reset” ( press reset once only )

•  Oil valve may be closed.

•  Oil supply may be too low.

•  Blocked flue sensor “tripped”

•  If the oil burner fails to start or runs for only a few seconds, call a qualified service technician.

Summary of Contents for SMO112






Reviews: