background image

 

9. Doors                                                                                                                       Summer Garden Buildings – Hipped Summerhouse 270 

Open the hinges out flat on the left door. Position the door as shown below with the hinge flat against the frame of the front panel. Align the hinge so that the knuckle sits 
forward of the panel. Adjust the height of the door to fit centrally in the gap and secure the hinge in place using 24 x 25mm screws. Repeat for the right-hand door. To fit 
the  door handle. Push the door lock into the rebate on the edge of the right-hand door as shown and secure using 2 x 25mm brass screws. Push the metal handle bar 
through the door latch mechanism. Fit a door handle to the metal handle bar on each side of the door and secure them in place using 4 x 30mm black countersunk screws 
per handle. On the other door fit the lock plate using 2 x 25mm brass screws. With the doors fitted adjust the distance between the front panels to allow the doors to shut 
properly then tighten the front panel screws to lock their position. Please refer to section 3.  

Side view  

 

Hinge knuckle sits  
forward of the front  
panel  

Front panel frame  

 
 
 
 
 

25mm  

Hinge knuckle  

 
 
 
 

Door  

 
 

Front of  
assembly  

 

25mm  

 
 
 
 
 
 
 
 
 
 
 

25mm  

 

Metal handle bar  

 
 
 
 
 
 
 

Important Note:  
Once the doors are fitted adjust the distance between the  
front panels to allow the doors to shut properly then fully  
tighten the screws at the top of the front panels to lock the  
position. Please refer to section 3.  

 
 
 

30mm  

 

 

10. Door weatherstrips and beading  

To the right-hand door position a weatherstrip over the join between the 2 doors and secure in place to the inner door only using 4 x 38mm screws. Position a second 
weatherstrip in the same position on the left-hand door and secure in the same way to the inner door only. The third weatherstrip is positioned on the left hand door so that 
it overlaps the edge of the outer door, secure in place with 4 x 38mm screws. Fit the beading strips to the frame of the front panels as shown below and secure in place 
using 5 x 20mm nails per strip.  

For each screw drill  
a 3mm pilot hole in  

3mm 

the   weatherstrip 

Drill 

only. 

 
 

Overhead view of left-hand door and front panel 

beading fitted to the front 

panel framing.  

 

Weather strip overlaps door  
edge.  

Left front panel  

 
Left outer door 

Left inner door 

 
 

Weather strip overlaps both  
doors and secured to inner  
door only.  

 
 
 
 

Overhead view of right-hand door and front panel 

20mm 

 

beading fitted to the front  
panel framing. 

38mm 

 

Right front panel  

 
Right inner door 

Right outer door 

 
 

Weather strip overlaps both  
doors and secured to inner  
door only.  

 

For sales advice before you buy phone Summer Garden Buildings free 7 days a week on 0800 9777828

Summary of Contents for Hipped Summerhouse 270









Reviews: