Suhr A.C.E User Manual Download Page 16

NOTE: This product has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial 

environment. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 

manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this product in a residential area 

is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense. 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful 

interference. 2) This device must accept any interference received, including interference that may cause undesired operation. 
Notice: The FCC regulations provide that changes or modifications not expressly approved by J.S. Technologies Inc. could void your authority 

to operate this equipment. 
These limits are designed to provide reasonable protection against harmful interference in a non-residential installation. However, there is no 

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference with radio or television 

reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more 

of the following measures: 
• Reorient or relocate the antenna of the radio/television receiver. 

• Increase the separation between this equipment and the radio/television receiver. 

• Plug the equipment into a different outlet so that the equipment and the radio/television receiver are on different power mains branch circuits. 

• Consult a representative of J.S. Technologies Inc. or an experienced radio/television technician for additional suggestions. 

Summary of Contents for A.C.E

















Reviews: