manualshive.com logo in svg

SUGATSUNE LAMP FD80-AFH, Installation Manual

Share
Download
SUGATSUNE LAMP FD80-AFH Installation Manual Download Page 13

13

Right angle

Pull the wrench at a right angle 
away from the door.

*

Frame

Frame

⑫

Door stopper

   (Optional)

Up

Down

PP

PP

①②

Holder 

Installing Door stopper

⑫

 (Option)

&RQÀUPLQJ7ZRZD\VRIWFORVHURSHUDWLRQ

Make sure to install the Door stopper

⑫

 when vertical frame is not used.

(1)   Slowly move the door toward door head, and confirm that sliding 

door closer starts its function at approx. 100 mm before full-close 
position.

(2)   Also, confirm that the door closer starts its function at approx. 100 

mm before full-open position.

If the closer is not working correctly, check the Troubleshooting 
section.

8

7

Adjustment of door height

(1) Remove the support under the door.
(2) Turn the bolt and adjust the height of the door.

The height adjustment range is +4 mm to -4 mm from factory setting 
(totally 8 mm).
(Tool: nominal 10 wrench, max. 6 mm thick)

(3) After adjusting the door, pull the wrench at a right angle away from the door.

Make sure the width across flats of the bolt head is as shown in the figure*.

6

Leading edge

Trailing edge

①

Trigger

about 100 mm

about 100 mm

①

Trigger

(4) Insert the holder as shown below.

Summary of Contents for LAMP FD80-AFH















Reviews:

No comments

Brands by name

Popular brands

Load more brands